How long will it take to sink an open and empty vessel 4 m x 4 m x 2m high, with a  draft of 1.6 m, when 85 mm Ф dia, hole at it bottom is opened C= 0.75. A. 135sec B. 268sec C. 311 sec D. 220sec

Q: Determine the moment of the 2.7 KN force about point A?

A: BCAC=tan45BC=AC=3

Q: Estimate in (m/sec) se= 1572o Pa し-30.48 n = O-000045 M= 0.01 Pa.s 1: 1200

A: step 1-

Q: 3. The given triangular AB gate is hinged at A. Determine the weight of the gate that is required to…

A:

Q: 02. Given the figure below determine the velocity (In fps) of block A as it hits tho surface 410 b-…

A: To determine the velocity of block A as it hits the surface at B.   Given, Weight of block A (WA) =…

Q: Compute the average end volume (in cubic yards - yd') using the figure below: Sta 25+00 2,356 3,336…

A:

Q: A rectangular tank full of water is 2 ft wide and 18in deep. What is the force due to water pressure…

A:

Q: Which of the following is equal to 200 grads? Group of answer choices a.3000 mils b.1/3 rev c.π/3…

A:

Q: Small objects are delivered to the 83-in. inclined chute by a conveyor belt A which moves at a speed…

A:

Q: H=81.137 O H=91.137 O H=71.137 C H=61.137 Exz- If the lowrate between two tanks is (o.s m/s), And…

A: To Determine Head loss, H

Q: | 1000 m/s 40 deg Dm min ax² + bx + c = 0 ⇒ x = -b ± √b² - 4ac 2a 750m A projectile is launched with…

A: A projectile of launching velocity 1000 m/s at an angle 400 with the horizontal is given in the…

Q: One machine has a setup cost of $400 and a unit cost of $1.50, and another machine has a setup cost…

A:

Q: An open rectangular tank measuring 5 m long, 1.82 m wide, and 2 m high is filled to a depth of 1.6 m…

A:

Q: Only  answer if pump will meet demands, show work justifying answer and the pump size that is…

A: The given data is shown below: Length of pipe=100 mDiameter of pipe=50 mmDischarge=370 l/min

Q: Example: A k E = 2*10³ kN/m² I = 1 *10-4 m4 20 kN/m 4m Required: AB Ο 21 * 2m C * QAD nswers in…

A:

Q: what diometer of new cast iron pipe to discharge 120 liters / sec of water with a of not more than I…

A:

Q: If the hydraulic cylinder AB is extending at a constant rate of 1 ft/s, determine the dumpster's…

A: Given: Hydraulic cylinder AB extending at constant rate, V= 1 ft/s  To find out Angular velocity…

Q: volume of the parallelpiped

A:

Q: 2000 N/m 1500 N/m W 1000 N/m - A в 0.3m 0. Sm 0.2m 0. 3m 0.15m 0.15m

A:

Q: Calculate the splitting volume based on the information given below. yarma A1=200 m2 A2=300 m2 dolgu…

A:

Q: Please include free body diagram The head of water over an orifice of diameter 100 mm is 5 m. The…

A:

Q: PROBLEM 6: A float to be used as a level indicator is being designed to float in oil, which has a…

A:

Q: Small objects are delivered to the 66-in. inclined chute by a conveyor belt A which moves at a speed…

A:

Q: Waner flows steadily trom the large open tark shown below. if viscous effects are neglgtle,…

A: We have to find Discharge Q

Q: An open cylindrical container 800 mm in diameter and 1.50 meter high contains fresh concrete (s=…

A:

Q: Is it 49.3 kN down or up???

A: This question is related to the Structure Analysis. In this question Reaction at B (Rb or By ) will…

Q: Q1 A bar as shoon 5000 N A- 500 mm E, 200 GPa T 15°C T2: 70 C Octermine O oin O If the bar sabpetek…

A: GivenA=500 mm2E=200 Gpa=200×103 mpaT1=150 cT2=700 cα=11.7×10-6firts…

Q: 5. What is the factor of safety against overturning for the triangular dam? Determine the pressure…

A:

Q: A system of three pipes 600 m, 800 m, and 1000 m long that are connected in series carries 600 L/sec…

A: Length of the first pipe (L1) = 600 mDiameter of the first pipe (D1) = 450 mm = 0.45 mLength of the…

Q: Water can jump from a depth of 30 cm to 75 cm in a rectangular flume. The flume is 2.75 m wide. What…

A: Depth before jump (y1)=30cm Depth after jump(y2)=75cm

Q: A shift with surface area =0.0549 m2 is being pushed at a speed of 400 mm/s through The clearance…

A: Newton's law of viscosity defines the relationship between the shear stress and shear rate of a…

Q: 5. What is the factor of safety against overturning for the triangular dam? Determine the pressure…

A:

Q: V Dre Matm Ot *Exercise 1: The gale 90 is suhjected to waler pressure as shown in figure. Find (Fy…

A: To find Fh and Fv

Q: A car, weighing 65000 lbs, travels at 50 m/hr, at the foot of an incline of 5%, the engine is turned…

A:

Q: Example Problem 3: Determine the value of P just sufficient to start the 10° wedge under the 400lb…

A:

Q: Cd-1:0 Derive the coa.ation. o Motirn in terms o height 21 meor empyting the Fank Pen tom 5m

A: Introduction- Motion: A object is considered to be in motion if its placement with relative to a…

Q: The beam is subjected to the loading shown. If a = 180 mm, determine the absolute maximum bending…

A: Absolute Max Stress = 105.105 MPaExplanation:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.