HORIZOΝΤAL LINE BEARING MEASUREMENT А-В N 13° W 1.118m В-С N 58° E 1.029 m C-D S 6° E 0.953 m D-E S 24° E 0.914 m Using the concept of vector system, what is the resultant of all the lines, having their magnitudes as the lengths, and directions as the bearings?

Q: 2. By using AreamomentMethod, Determinethedeflectionatthefreeendof thebeamshown 180 kN 15 kN/m В D…

A:

Q: 3. Byusing Area MomentMethod, Determinethe deflectionatthefreeendofthebeamshown 60 kN 300 kN-m A 5 m…

A:

Q: Q2) For the system shown in (FIG.Q3B) determine the resultant and locate it w.r.t. point A? 1150 N…

A: Given: Forces = 200N , 150N , 250N and moment =300 Nm

Q: The difference between bearing and azimuth is that .... Select one: O a. Azimuth is measured counter…

A: Approach to solving the question:The correct answer was identified and explained. Detailed…

Q: indicated to the horizontal neutral axis. The girder is also supporting a mass of 5000kg 30kN 20kN…

A:

Q: | ZAO O "l zain IQ 10/10 find the strain( €) in x-axis only. if Poisson ratio=0.25, E= 200 .GPa 14…

A: Given data Loads Area of cross sections Modulus of Elasticity  Poissons ratio

Q: Experimental, Values, N Trials Computed Values, N Percent Error RA .6659kg 6.5258 N 6.5333 N 0.11…

A:

Q: Problem: Replace the force system acting on the post by a resultant force, and specify where its…

A:

Q: ISL TL = 499.9666667 --20)382) A horizontal distance of (500 m) must be lay out with a steel tape,…

A: Given values: Measured condition: Temperature: Tm = 50 degree C Tension = 120 N Pull: Pm =…

Q: The resultant of the two forces has a magnitude of 932 N. Determine the magnitude of P using Law of…

A:

Q: Determine EI8 at point Band end of the overhang. Round off your final answer in 2 decimal places. W1…

A: Given  W1= 34KN/m , W2=30 KN/m  X1= 7m , X 2= 6 m  X3= 5m

Q: 1. TRA 12kN 30° 5M 12kN 847 60 с 3RN D 5M E + 2kN -T 5μ 2K41 G Determine using method of section the…

A: To find the nature of the forces in AB, AC , BD, CD and CE using the method of sections.

Q: Q3: Compute the reduced bearings of all sides of the following trverse. If AB = S 72° 39'W %3D B A…

A: The reduced bearing or quadrantal bearing system of measurement measures the angle from the north or…

Q: 2. Find P, Q, and C if R = 75000 N.mm у 100 N 12 A 30 mm 400 N 3 t -30 mm B

A:

Q: For the frame shown below, where: L-5 m q=6 kN/m P=17 KN Compute the displacement at D in mm…

A:

Q: Q2) For the system shown in (FIG.Q3B) determine the resultant and locate it w.r.t. point A? 150 N…

A:

Q: Q. 4 A = 500 , Pressure diff: b/w too limbs can be measured by measurement on Bne limb Then findl he…

A: A=500a To find error induced in measurement

Q: 4. Line AB was measured and the result is 834m. It is measured using a 30m tape that is 0.002m too…

A:

Q: 3. For the system forces shown, solve the following: (the coordinates are distance in meters from…

A: Given  Forces F1 , F2 , F3 , F4 and their coordinates ..     Clockwise moments = negative…

Q: MA "(A RA 20 KN 20 KN MB KAB = 10.67x10⁹ -3 m3 m3 m4 m RB 60 KN KBC=9x10⁹ 4 m- a. Construct the…

A: Given: Required : Moment distribution table Moments Reaction

Q: y 400 N 3 2 30° 1 300 N 1 X 700 N

A:

Q: Problem: Replace the force system acting on the post by a resultant force, and specify where its…

A:

Q: MALI + 2 MB (L₁ +4₂) + McL₂= = GAIX - 6 Az X z Li L2 pM2Q w(KN/m) B L (m) Draw the V&M Diagram using…

A:

Q: Compute the FR and ϴx on a 1 m wide strip of the gate shown.

A: Objective: To determine the resultant force on the gate and the angle made by the resultant with…

Q: St ress quadric of Cauchy given by

A: Stress quadric of caichy given by                                                        = t1*t2= +-…

Q: EA 2: AREA-MOMENT & CBM Solve for the EIA of the ff: GOKN SOKN AMM & CBM 22 BJ * D F 3m 2m 2.5m EIA…

A: Given simply supported beam with two point loads of magnitude 50 kN and 60 kN .It is asked to…

Q: determine d.? Ey B) Ex 75H de de Ax CO D. 2kps 2 kips 64 75H D) de 10E d6 de A

A: 1) option A  2) option b

Q: D Shaft is getting twisted. Shaft diameter is D and Material Shear Modulus is G. How much Torque…

A: The answer is found to be Torque T = 62.66 N.m For explanation please refer the attached solution,…

Q: Solve the critical value of P under LRFD Method

A:

Q: Q1- Calculate A,B and C the Vertical movement of points steel wine Dez5mm steel wire 3m D=25 mm E.…

A: Given P=28kN D=25mm E=2×104N/mm2 To find  Movement at A,B and C

Q: Is this way simplier to got AY, BY, AX,BX find out? Can u simplier that equations, i don't got…

A: Given, 4Ex + 4Ey = 9.02.....................(1) -3Ex + 3Ey= -4.5.....................(2)

Q: In the figure, what is the slope of member EM ? 3 KN 2 KN 6 KN 8 KN 6 KN 2 KN 3 KN 0.50 m J 6 @ 1…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.