horizontal drilling

Q: A helical compression spring made of a wire of circular cross-section is subjected to a compressive…

A: Given:initial shear stress=24 MPaτ1=24 MPa

Q: A long plastic rod of 20-mm diameter (k = 0.3 W/m-K and pc, = 1040 kJ/m3.K) is uniformly heated in…

A: Given: The diameter of rod, d = 20 mm = 0.02 m The thermal conductivity, k = 0.3 W/m.K The…

Q: 5 A metal has the following flow curve equation of O, = 850€ 03 where o, is in MPa. A part made of…

A:

Q: 2.40 A gas is compressed in a cylinder by a movable piston to a volume one-half of its original…

A: Option d is correct

Q: lar cross section of radius ne figure. The two parts an ch. Calculate the tension in

A:

Q: A 10-hp pump (installed a the ground level) draws water from a well 30 ft below ground level ane…

A:

Q: 3. For the link mechanism if wAB = 2 rad/s as shown, determine WBc when 01 02. Find %3D %3D also Ve…

A:

Q: Please send Complete answer for getting upvote  Detailed answer  what is Flyweight Design Pattern…

A: given; what is Flyweight Design Pattern Application  Real world example

Q: The graph on the left shows a particle's position as a function of time. a. Which graph on the right…

A:

Q: 0.75 m 1.0 m 1.5 m Figure P5.103 6 m 3 m

A:

Q: In an air conditioning system, the inside and outside conditions are dry bulb temperature 24°C,…

A:

Q: We are considering a homogeneous linear system Ax b, where b = 0 and with A being an nxn, then the…

A: From Homogeneous linear system Ax = b  Where b = 0 One solution is non zero then it is non trivial…

Q: The figure below represents the geometry of a beam that has a T-shaped cross-section. W h Find the…

A:

Q: 9 Derive Equation 7.16, which gives the relationship between the nozzle loss coef- ficient A, and…

A:

Q: Which of the statements about normal error distribution is false?

A: Option (a) is correct. Means it is showing a false statement. for a special case , standard normal…

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: Course: Manufacturing Process How To Perform Tapper Turning of a Rod by Tail Stock Offset Method?

A: Given data How To Perform Tapper Turning of a Rod by Tail Stock Offset Method

Q: 20) A progectile is shot from the origin with an înitial Speed of Ut = 25 m at an angle e with…

A:

Q: 3. Determine the magnitudes of the pin reactions at A and C. Neglect the weights of the members. 800…

A:

Q: For a system of springs shown below, assuming that all springs are identical with stiffness of k the…

A:

Q: A force Plt) acting on the Pistor Causes Crankshaft AB to rotate . The mass per each Bar ús T, uunit…

A: Solution: Given Data: mb=σmp=σL

Q: "). A drawing operation is used to form a cylindrical cup with inside diameter = 75 mm, height = 55…

A:

Q: In exponential smoothening method,

A: Given; Exponential smoothening method,  Which one of the following is true,Where,   Exponential…

Q: A full journal bearing has a journal diameter of 1 in, with a unilateral tolerance of -0.0006 in.…

A: Given:dmax=1.4in                        l= 2.24in                   N=849.8297 rev/minbmin=1.402in…

Q: Consider a spring-damper vibration isolation system for a microscope of mass M (shown). harmonic…

A: As there is no any isolation so by decreasing the eccentricity transmitted force get reduced

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: Refer to Fig. 8-27 below. The weight of A is 50 lb; the weight of B is 80 lb. The coefficients of…

A:

Q: Cleaning of machine tool should be carried out daily. Select one: True False

A: When it comes to machine tools, it's extremely important to perform the proper maintenance on them…

Q: Obtain a state-space representation of the mechanical system shown below, where u₁ and u₂ are the…

A:

Q: You are designing a spring-damper vibration isolation system for a microscope (shown). Wn is a…

A:

Q: to 4 MPa. Determine the final temperature of the water and the work required, in kJ/kg, for this…

A:

Q: A cylindrical part for the shipping industry is 375 mm long and 150 mm in diameter. 1000 of these…

A: Given:

Q: For what value of w (frequency of the forced harmonic excitation) does the system described by ÿ+9y…

A:

Q: 1. What type of tool is it? 2. What is its main purpose? 3. What secondary functions does the tool…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: . Show that Eq. 17.34 is approximately correct over the Reynolds number range from 3 · 103 to 105 by…

A:

Q: In the cam-follower mechanism shown, the cam has a total height of 5.25 cm and a base circle radius…

A: Given: Total height of the cam→h=5.25 Cm Base circle radius→r=1.75 Cm Length of the arm→a=10 Cm…

Q: ACCURATELY

A: We have given ACCURATELY

Q: Double cut files use a second set of teeth,perpendicular to the first set to produce a rougher…

A: The given statement is “Double cut files use a second set of teeth perpendicular to the first set to…

Q: Force vs. Defection 70 60 y = 118655x 50 40 30 20 10 0.0001 0.0002 0.0003 0.0004 0.0005 0.0006…

A:

Q: 1. Calculate coordinate of P with respect to (Xo, Yo).. 1= 2 12= 3 01 =30° 02=20° Y2 yo p°(x,y) Y1…

A: The coordinate of P wrt (x0,y0) is given as - x-coordinate wrt x0=l1cosθ1+ l2cosθ1+θ2x-coordinate…

Q: What is the sliding block?

A: To Define: Sliding block

Q: A point on a thin plate is subjected to the three successive states of stress shown. Determine the…

A:

Q: Angle of bite in radian ?

A: Given data; Single pass rolling process;  Diameter, d=420 mm  Width, b=145 mm  Thickness,t=9 mm…

Q: A thin water (density 997 and dynamic viscosity 0.001009 Pa.s) sheet of 2.127 mm thickness, slides…

A: Ans: option (d) is correct.