Homework # 2 : A p-n junction diode has a reverse saturation currentrating of 50NA at 32°C. What should be the value of the forward currentfor a forward voltage drop of 0.5V (Assume 32°C)? Calculate thedynamic ac resistance at 32°C and a forward voltage drop of 0.5V ?dv/dt dVD VDdi/dt dlpNote: dynamic resistance =%3DID

Answered: Image /qna-images/answer/ad377124-fc74-4c21-963f-0585ba0c7b87.jpg

Homework # 2 : A p-n junction diode has a reverse saturation current ating of 50NA at 32°C. What should be the value of the forward current or a forward voltage drop of 0.5V (Assume 32°C)? Calculate the lynamic ac resistance at 32°C and a forward voltage drop of 0.5V ? dv/dt dVp VD %3D Note: dynamic resistance = %3D di/dt dlp Ip

Homework # 2 : A p-n junction diode has a reverse saturation current ating of 50NA at 32°C. What should be the value of the forward current or a forward voltage drop of 0.5V (Assume 32°C)? Calculate the lynamic ac resistance at 32°C and a forward voltage drop of 0.5V ? dv/dt dVp VD %3D Note: dynamic resistance = %3D di/dt dlp Ip

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
In the circuit given in the figure, find the current passing through the diode in mA since R1 = 4.95Kohm, R2 = 2.50Kohm, R3 = 1.69Kohm, R4 = 5.44Kohm, VCC = 13.00V and the diode is silicon?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
Here are some statements about a p-n junction diode. Some are TRUE and some are FALSE. i. Applying a negative bias to the p-side and a positive bias to the n-side allows a forward current flow. ii. When the p-n junction is under reverse bias, the Fermi level is continuous across the junction. iii. The forward bias current is made up of holes from the p-side and electrons from the n-side flowing across the junction. iv. Under reverse bias, you can get minority electrons flowing from the p-side to the n-side of the junction. v. To get a large built-in voltage, you need to heavily dope the p-side and n-side of the junction. vi. The built-in voltage (or contact potential) of a p-n junction is typically twice the value of the band-gap of the semiconductor. Which of the following statements is correct: (i) and (ii) are both FALSE (ii) and (v) are both FALSE (iii) and (vi) are both FALSE
perform dc analysis on a multiple diode circuit plz
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo
A silicon diode has a saturation current of 5nA at 250C. What is the saturation current at 1000C? For the given series diode configuration, determine Va, Is, and Vz. Si EE 10 V (a)