hi B RA

Q: The timber beam has a width of 6 in (Figure 1). The beam has the cross section shown in the figure…

A: Draw the free-body diagram for the system.

Q: Figure Q6 shows the cantilevered 6061-T6 aluminum alloy rectangular beam fixed at A. Given Modulus…

A:

Q: 2- Determine the minimum width b of the beam shown in the figure belov the flexural stress is not to…

A: The free body diagram is,

Q: The strut on the utility pole supports the cable having a weight of P = 300 lb. (Figure 1) Figure…

A: Given:The weight is .Free body diagram:     The triangle is obtained by multiplying by 2 for…

Q: the beam shown in Figure (2), determine transverse shear stresses E, F and G on the cross section.…

A: Given P=100kNINA=470016mm4

Q: 2. Given the box beam shown below, and concentrated load P=3500#. a. What is the magnitude of the…

A:

Q: Beam with cross section area shown in fig (2), the length (L =500 mm), effected by tensile force (F…

A:

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: The beam W24x104 beam is constructed of A-36 steel. AC has a cross-sectional area of 1 square inch…

A: For W24×104,I=3100 in4For A-36 steel,E=210 GPa=3.046×107 lb/in2, The deflection due to the UDL of…

Q: 8 For the beam shown, find the flange width (b) so that the allowable stresses O₂ =30 MPa and 0₁ =…

A: to find: 1) Flange width (b) = ?2) load that can be applied (w) = ?

Q: 3. A solid cement rectangular lentil (beam) with length L = 1. 5 m is positioned as shown. The…

A: Given: L=1.5m The lintel is fixed supported on the left like and simply supported on the right.…

Q: In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.2 ksi. Ift =…

A: (a) Draw the free-body diagram of joint A.

Q: A tapered bar AB of solid rectangular cross-section with a thickness of 20 mm and length L = 800 mm…

A: To Find : The  elongation of the bar due to load P . Given :  The thickness is t=20 mm The length…

Q: determine the internal loadings at points D

A: determine the internal loadings at points D

Q: A simply supported beam -b<y<b, 0 <x<L, as shown below, is subjected to a compressive load of half…

A: σy= -3  4bx δ2Mδx2[y33b2-y] +c3f(x)+c4σy=0 at uy=-bc3f(x)+c4=34 δ2Mσx2 x 23=      σy=-3…

Q: Axial Loadings Consider the figure shown. A rigid beam is pinned at one end and supported by two…

A: For solution refer below images.

Q: Q2: For the beam shown in Figure (2), determine transverse shear stresses at points E, F and G on…

A: Find the transverse shear stress .

Q: a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural…

A:

Q: the dimension (in mm) of cross section from strength calculation            a = ?

A: allowable stress = yield stress/ FOS = 240/2 = 120 MPa well evaluate bending stress.

Q: Q2: For the beam shown in Figure (2), determine transverse shear stresses E, F and G on the cross…

A: GivenP=100kNINA=470016 mm4

Q: 1.Calculate total deformation 2. Minimum stress of the beam 3.Maximum stress of the beam Question 2…

A:

Q: Safe normal and non-slip of wooden beam material stresses are respectively σem = 10 MPa and τem =…

A:

Q: There is no F1 or F2 force, only P against the front end of the beam. Thank you so much for any help…

A: Given data-P=5KN=5000Nσy=240 mPa=240 ×106 N/m2

Q: * For the cantilever beam shown. find the value of Normal stress due to :axial load at point C 4 KN…

A:

Q: A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear…

A: A solid steel bar of circular cross section has diameter d = 40 mm = 0.04 m, length L = 1.3 m and…

Q: a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3000 lb box beam wall thickness, t = 0.610 in. diameter…

A:

Q: Consider the beam shown in (Eigure 1). Take P= 3 kip and w=1.3 kip/ft. Point E is just to the right…

A: According to the given data A loading beam ABC is provided  We need to find Normal force at point D…

Q: For a steel circular cantilever beam, 10mm in diameter, 700mm in length with an applied load of…

A: M= (3/4 My + 1/3 Mp)My = 24543.5 N.mmMp = 41666.66667 N.mmYield strength= 250 MPad = 10 mmy = d/2F =…

Q: q = 96 KN/m L = 25m El = 2500 Kn.m A B EI Rotation at Point B is . (positive if counter-clockwise)…

A:

Q: Box Beam Box Beam Support at A a b с a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3300 lb box beam…

A:

Q: Draw the shear diagram Draw the moment diagram Find the Maximum deflection

A: We can answer up to 3 subparts only so we will answer first 3. Please resubmit the question by…

Q: 2) The beam below consists of a material with a modulus elasticity of E= 70 GPa and is subjected to…

A: The moment applied is .The modulus of elasticity is

Q: (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At…

A: for solution refer below images.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.