Hey hows it going, this is a problem from my Structural Analysis course. I am havinig trouble understadning dead loads on girders. The solution is posted on Bartleby. For the dead loading acting on the girder AG, the solution only accounted for the weight of the girder itself. This does not make sense to me because doesnt the girder also support a portion of the concrete slab? Thanks!

Q: Briefly explain the difference between Ultimate Limit State (ULS). Stability, and Serviceability…

A: Ultimate Limit State: The ultimate limit state is also known as the Load and Resistance Factor…

Q: Question 4 Multiple Choice [Note: There is only one correct answer.] 1. An open-web joist girder is…

A: Open Web Joist- These are framing structures used widely in construction. It is generally made up of…

Q: Gentlemen, This task I think has a trick. I Red that metal is there for reinforcement only, it does…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: (1) Considering the figurat use yout of the frame नि Our answer below, we assume Structure is…

A:

Q: Q # 1: Design main reinforcement and shear reinforcement for beam carrying total design load…

A: To design the following beam in the question, check the procedure below. Given data- b= 200mm D=…

Q: The beams are to be designed assuming they are supporting uniformly distributed line loads, not…

A: Beam AB3 will support half of the load of width 2-3 and 3-4

Q: Problem II. The fabricated steel members are being assembled into a truss on-site in the…

A:

Q: If a wide-flanged beam fails in local buckling of the flange, will the top flange, the bottom…

A: When the beam section is subjected to large amount of stresses or loads, the thin sized members as…

Q: 67. In case of damaged prestressed concrete I girders which are used for restoring strength? A. O…

A: POST TENSIONING CAN BE USED TO STRENGTHEN DAMAGED PRESTRESSED CONCRETE. HENCE OPTION  B IS CORRECT.…

Q: Identify what type of structure is shown. Hinge Hinge a. Frame b. Truss C. Beam d. Arch Type of…

A:

Q: The building construction is cast-in-place conventionally reinforced concrete. What is the maximum…

A: This question is related to the Design of RCC structure from Civil Engineering. In this question ask…

Q: Problem II. The fabricated steel members are being assembled into a truss on-site in the…

A: Gap = 4.09mm. [Note : Ignore axial deformation of member CD when applying load P]

Q: 17.3 A 1-in.-by-4-in. steel bar is subjected to the loads show Calculate the combined stresses at…

A: Given Data -  Cross section of Bar = 1 × 4 inch  Load P1 = 12000 lb . P2 =1200 lb  Find -  Combined…

Q: two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @…

A:

Q: 67. In case of damaged prestressed concrete I girders which are used for restoring strength? A. O…

A:

Q: flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports:…

A: Percentage of steel is equal to  Pt= area of steel in tension / effective area of concrete Pt = Ast/…

Q: Why are rollers used as support and loading mechanism in flexure instead of just using a simple…

A:

Q: How the concept of Principal Stresses is is used in Everyday life and in industry?

A: Answer:- Principal stress:- Principal stress is  the maximum or minimum normal stress acting on any…

Q: 1) It is not necessary to install reinforcing steel in concrete under compression? Tor F 2) Nominal…

A: Brief concept introduction- Reinforcing steel- These are the steel bars that are used with the…

Q: temporary framework

A: To find:- Which temporary framework is known as and that will be useful in construction demolition,…

Q: A timber beam shown in the figure is made up of Sasalit (50% stress grade). Use LRFD. All thegiven…

A:

Q: two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @…

A:

Q: In prestressed concrete beams, draped or harped tendons are usually used instead of straight…

A: The prestressed concrete is defined as “the process of inducing the internal stresses in the…

Q: What is the vertical Pmax only considering Buckling? Use AISC recommended Leff. b) Horizontal Pmax…

A: Length of flag pole = 14 footYield strength = 36 ksiE= 2.9 * 10^7 psioutside dia , d0=8inchwall…

Q: 65. In some cases of repairs of girders damaged by collision, the damage is severe what is used? A.…

A:

Q: A single rivet is used to join two plates as shown. If the diameter of the rivet is 3/4 inch and the…

A:

Q: can you answer this problem for me, this will serve as my reference in solving this kind of truss in…

A: Using equation of equilibrium,MC=0VA×4=4×2-3×1.5VA=.87kNupwardUsing FY=0, we…

Q: f'c = 4ksi; by = 60ksi Stimups #3@4" 4/c @ WHAT IS THE DESIGN SHEAR CAPACITY OF THE BEAM? [*V₁ =…

A:

Q: Check the following reinforced concrete beams for bending. The beams are on a simple span of 26.5ft.…

A: Loading : 3.20 kip/ft live and 1.80 kip/ft dead excluding beam weight. L = Simple span length =…

Q: 67. In case of damaged prestressed concrete I girders which are used for restoring strength?

A: Prestressing is method in which initial internal compressive stresses are induced before loading it…

Q: The same wooden centering was used four times to form this concrete arch bridge.

A: Centering is the type of temporary framework which is laid under the structure to keep that…

Q: hear and flexure only is reinforcnd as follows: TOP BARS BOTTOM BARS @ MIDSPAN 2-016 mm 3-016 mm @…

A:

Q: All question pertain to the following floor plan. The floor load is 60 lb/ft2. Ignore the self…

A: Consider the free body diagram; Calculate Uniformly distributed load on beam B1 Udl=…

Q: Problem II. The fabricated steel members are being assembled into a truss on-site in the…

A:

Q: maximum uniformly distributed load which can be carried by the beam on a 4 m simple span.

A:

Pricing Concrete Work

The concrete work in a project usually holds a high-end cost in terms of cost and value of the work. It becomes an important step in calculating the cost associated with concrete while preparing the project scale. The cost of making concrete depends on the cost of building materials, mixed materials, labor, and machinery. A concrete contractor builds structures from concrete, usually managing all the steps of the process from assembling ingredients to building a holding structure and preparing the mixture. This person or team oversees the delivery and unloading of goods to ensure that they are done properly. Nowadays, most of the concrete in the United States comes from manufacturers working abroad, usually with branches and plants within the provinces. Contributions can range from pre-mixed concrete to basic ingredients, the consumer company then mixes it. Many American-based concrete companies, however, offer concrete products, such as ballads, bricks, countertop, concrete pipe, and building products, as well as concrete construction and installation materials. This article covers both types of suppliers for this set of building materials.