Here is a single phase transformer, 15 kVA, 15000/380 V, 50 Hz has Ze-0.02+j0.05 perunit, R. 50 perunit, and Xm =30 perunit, (per unit= actual value/base value), for scaling of the problem. (pu). A) Compute and draw the equivalent circuit components in Qs referred to the low-voltage side, B) Low voltage side is connected to a load of 4L 90° (lagging) and HV side is supplied by 15KV, compute voltage drop on the load V2 and voltage regulation VR.

Here is a single phase transformer, 15 kVA, 15000/380 V, 50 Hz has Ze-0.02+j0.05 perunit, R. 50 perunit, and Xm =30 perunit, (per unit= actual value/base value), for scaling of the problem. (pu). A) Compute and draw the equivalent circuit components in Qs referred to the low-voltage side, B) Low voltage side is connected to a load of 4L 90° (lagging) and HV side is supplied by 15KV, compute voltage drop on the load V2 and voltage regulation VR.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
A 200-kVA, 230-V/230-kV testing transformer having a resistance and leakage reactance of 2% and 7% respectively, is to be used as a resonant transformer at 50 Hz to test a piece of cable at 400 kV. The load capacitance is 0.01μF and inductor coil is assumed to 3% resistance. Determine the series inductance required and the input voltage. ..
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
QUESTIONS: 1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measured values of these tests? 2. The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformer tested at 50 Hz: Voltage (V) Current (A) Power (kW) LV winding with HV terminals open-circuited: 3810 9.86 8.14 HV winding with LV terminals short-circuited: 920 141 10.3 a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltage winding. b. Calculate the…
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
Do the following: Solve for the voltage across the appliance and the current through it by referring the appliance to the transformer primary. (Assign the convenience outlet voltage as the reference phasor i.e. at 0o) Draw the circuit that would solve for VL and IL. Compute all referred values and label all components. Solve for VL and IL
1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. If standard open-circuit and tests were performed on this transformer, what would be the measured values of these tests? 2. The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformer tested at 50 Hz: Voltage (V) Current (A) Power (kW) LV winding with HV terminals open-circuited: 3810 9.86 8.14 HV winding with LV terminals short-circuited: 920 141 10.3 a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltage winding. b. Calculate the cantilever…
Three Phase Semi Converter When Highly Inductive Load Connected: Please derive the following equations for continuous conduction, Thanks :-)
Vr 3. For a 1.2 accuracy class potential transformer used at a lagging phase angle y of 10', the RCF value is A. 0.991. B. 0.988. C. 0.977. D. 0.999. primary connection scheme that must be used with
1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measured values of these tests?
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.