Heat Transfer Develop the heat diffusion equation for a cylinder starting from the energy conservation equation. State all assumptions. Define all variables in the energy conservation equation. Show every step in the process of getting to the final heat diffusion equation.

Heat Transfer Develop the heat diffusion equation for a cylinder starting from the energy conservation equation. State all assumptions. Define all variables in the energy conservation equation. Show every step in the process of getting to the final heat diffusion equation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ Consider a large plane wall of thickness L=0.03 m. The wall surface at x =0 is insulated, while the surface at x =L is maintained at a temperature of 30°C. The thermal conductivity of the wall is k=25 W/m °C, and heat is generated in the wall at a rate of g = 9oe0.5x/L W/m³ Where g, = 8 x 10 W /m². Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) determine the temperature of the insulated surface of the wall.
2000kg cast iron housing at 450 degree Celsius is quenched in 5000kg of water at 15 degree C. What is the amount of heat transferred to water, use specific heat of water to be 4.18 kJ/kg.K and specific heat of iron to be 0.42 kJ/kg.K
Heat Transfer question In order to cool down a hot steel sphere (its diameter is 5 cm), CO2 gas is blown over it through a pipe with a diameter of 10 cm. The CO2 gas is kept at atmospheric pressure while moving through a smooth pipe at a speed of 6 m/sec. The gas temperature entering the pipe is 300K and exiting the pipe is 340 K. The pipe temperature at the entrance is 350K and at the exit is 550K. The sphere is located just about the pipe exit. Find the convective heat transfer coefficient of the gas moving in the pipe, the heat transfer rate at the pipe and the pipe length. What is the surface temperature of the sphere if the heat transfer rate between the sphere and the gas is 7W and its surface temperature is higher than the gas?
A spherical container having an outer radius r2 and inner radius r1 (with thermal conductivity, k) is filled with radioactive material generating constant heat at a rate of qdot. Fluid flows across the container at Tinfinity and convection coefficient h. Obtain a relation for the variation of temperature through the spherical container assuming steady state.
Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20 oC, TL=100 oC. The density, conductivity and specific heat of the material are ρ =800 kg/m3, k=200 W/m.K, and cp=2500 J/kg.K, respectively. Also, r1=10 cm and L=20 cm.
Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
The same engineer decides to look into rates of cooling for liquids toexperiment with different cooling solutions for servers. She finds thatthe rate of cooling for one liquid can be modelled by the equation:y = 48 × 0.99t(0 ≤ t ≤ 80)where y is the temperature of the liquid in degrees Celsius and t is thetime in minutes.(i) State whether the type of reduction for this model is linear orexponential. Describe how reduction rate differs between linear andexponential functions. (ii) Calculate the temperature when t = 20. [3](iii) Write down the scale factor and use this to find the percentagedecrease in the temperature per minute. (iv) Use the method shown in Subsection 5.2 of Unit 13 to find the timeat which the temperature is 30◦(v) Determine the halving time of the temperature.
A pipe carries hot molten lead from one part of a factory floor to another. The mass flow rate of lead is 0.05 kg/s. While trying to figure out the heat loss from the pipe, you found that over a 2-m length of he pipe the lead temperature drops from 580 C to 557.C. What is the rate at which thermal energy is being lost from the lead carrying pipe in this 2-m section? Use the property table to find out properties of lead as needed.
Please solve only part 3. This is a 3-part question involving heat transfer. Part 1 and 2 are correct, but I need help how to find part 3. Thank you.
The initial temperature of a 50 cm long silver wire is 50 °C. The circumference of the wire in question is completely insulated, but both ends are kept at a temperature of 0 °C (zero degrees Celsius). Obtain the heat conduction along the wire as a function of time and position and, taking a single term in the solution, determine how many degrees Celsius the temperature in the middle of the rod will be after 7 minutes. (For silver wire, α=1.70 cm2/s.)