he 2 m long tube, the cross section of which can be seen in the figure, is fixed at one end and a torque of 700 N.m is applied from the other end. Since the wall thickness of the tube is 3 mm, calculate the shear stress values at points a and c. Calculate the angle of rotation of the end of the tube where the torque is applied.

Q: ) Write the equation for the neutral axis in the cross-section. b) Draw the normal stress…

A:

Q: The state of stress at a point in a member is shown in A 0x' = 60° σ y B on the element. Assume ox…

A:

Q: The bar in figure has a constant width of 30 mm and a thickness of 20 mm. Determine the maximum…

A: The width of the bar = 30 mm The thickness of the bar = 20 mm To determine:-The maximum average…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 95 MPa and Sy =…

A:

Q: A plate with a 1.5-cm diameter circular hole is exerted with the bending moment M = 40 N-m. The…

A: Given bending moment , M = 40 Nm Sy = 400 MPa width of plate, b =3-dia of hole =(3-1.5)cm depth, d =…

Q: point, another plane B, inclined at 45°, on the normal aly Mohr's stress circle technique to find…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 60 MPa and Sy =…

A:

Q: a) A holiow steel tube used in a roof structure has an outer diameter, d; = 104 mm and inner…

A:

Q: A rod having a circular cross section (radius; 0.5 in, height; 15 in) is subjected to loadings as in…

A: torque at fixed end  T=540 lb.indiameter of shaft  d=0.5 inthen shear stress at  A abd B…

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

A: Find equivalent force and moment at the section a-a. Then using stress equation the state of stress…

Q: Figure Q3 (a) shows an overhanging beam ABC subjected to a uniformly distributed load w along AB and…

A: yield stress of the material is 250 MPa

Q: [0.0016 [o] = 0.0003 0 0.0003 0.0008 0 0 0 0.0004. a. Determine the strain matrix for this strain…

A: Data given Find:  (a) Determine the strain matrix for the given strain state if the x and y axes…

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

A:

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A: The given data is shown below: Sx=12.4 ksiSy=3.5 ksiSxy=3.6 ksiβ=29°

Q: e average normal stress

A:

Q: A rod and tube of cross-section shown in figure are firmly attached at their ends to form a compound…

A:

Q: The steel tube AB (see Figure 2) is fully fixed at its end A and free at B. It is subjected to a…

A:

Q: The following shaft consists of a 3.50 m long steel shaft and a 2.00 m long aluminum tube. The steel…

A:

Q: In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit…

A: the largest P value according to the Von Mises assumption for the cube to be safe = 20a23explanation…

Q: Q3) The aluminum tube shown in Figure (2) has a thickness of (5 mm) and outer cross sectional…

A: For equilibrium  280 = 135 + Tc Tc = 145 Nm Average shear stress τ=T2tAmMaxm τavg will be obtained @…

Q: Problem (4.4): The aluminum-alloy shaft AC in Figure (4.25) (G= 26 GPa) has an 800- mm-long solid…

A:

Q: 12 МPа 6 MPa 8 MPa

A:

Q: A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in the…

A: The thickness of plate = o.5inch Plate Shear Stress =  27ksi  Circumference of the punching Area = a…

Q: Problem Sets - 1: The thin-walled tube is used as a beam to support the uniformly distributed load…

A:

Q: Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam…

A:

Q: Knowing that the machine component shown has a trapezoidal cross section with a = 2.5 in. and b =…

A: A trapezoidal section is given on which a moment of magnitude M = 75 kip-in is applied, To…

Q: 2. A thin-walled steel tube has an outer diameter of 100mm and a material thickness of Smm. The…

A: Given Data Do=100mm,  tm=5mm, Fs=2, δu=250Mpa, δu'=520 Now inter-Diameter Di=100-5=95mm Now, by…

Q: The d = 15-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When…

A:

Q: (2) A square member (400mm x 400mm) sustains an internal shear force of 150 kN and an internal…

A: Given: A square cross section of 400mm × 400mm Shear force = 150KN Bending moment = 250KN-m…

Q: The following shaft has a diameter of 60 mm, and it is made of Aluminum (G = 29 GPa). The shear…

A: Given, d=60 mmG=29 GPaτ= 200 MPaFOS=2.5ϕ=3 degree

Q: A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure). T >> r2…

A:

Q: Consider a solid circular shaft fixed at one end and free at the other end with a concentrated…

A:

Q: For the link shown in the figure, the thickness of the link is 50 mm. Given that the force P= 40 kN,…

A:

Q: e pins are 1 cm in diameter and are made of 304 stainless steel. A distributed load of 200 N/m is…

A: Given:- two rigid bars with a 5cm x 5cm section A-36 steel. the pins are 1 cm in diameter a 304…

Q: The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of…

A:

Q: The plastic hexagonal tube shown in Figure (3), is subjected to a torque of 150 N. m. Determine the…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.