A solid bar having a diameter of 100mm is to be replaced by an elliptical tube having a cross sectional dimensions to the median line of the cross section as shown.

Q: The solid compound shaft made of three different materials carries the two torques as shown. (a)…

A:

Q: A plate with a 1.5-cm diameter circular hole is exerted with the bending moment M = 40 N-m. The…

A: Given bending moment , M = 40 Nm Sy = 400 MPa width of plate, b =3-dia of hole =(3-1.5)cm depth, d =…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take di = 30 mm,…

A: Determine the average normal stress at the midsection of rod BC.

Q: The steel tube AB (see Figure 2) is fully fixed at its end A and free at B. It is subjected to a…

A:

Q: A hollow steel shaft with an outside diameter of 115 mm and a wall thickness of 11 mm is subjected…

A:

Q: Q- The minimum shear stress in a hollow shaft of outer diameter 40 mm and thickness 5 mm subjected…

A: outer diameter 40 mm  thickness 5 mm torque = 10 Nm.

Q: The following shaft consists of a 3.50 m long steel shaft and a 2.00 m long aluminum tube. The steel…

A:

Q: Q3) The aluminum tube shown in Figure (2) has a thickness of (5 mm) and outer cross sectional…

A: For equilibrium  280 = 135 + Tc Tc = 145 Nm Average shear stress τ=T2tAmMaxm τavg will be obtained @…

Q: A solid 11 mm diameter shaft is subjected to an axial load of P-33 kN and a torque of Tacting as…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: The following shaft has a diameter of 60 mm, and it is made of Aluminum (G = 29 GPa). The shear…

A: Given, d=60 mmG=29 GPaτ= 200 MPaFOS=2.5ϕ=3 degree

Q: A shaft is subjected to a torque T. Compare the effectiveness of using the tube shown in the figure…

A:

Q: A flexible connectoin consisting of rubber pads (thickness t = 9 mm) bonded to steel plates is shown…

A:

Q: For the state of plane stress shown below. 74. Determine the largest value of σy for which the…

A:

Q: A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure). T >> r2…

A:

Q: Consider a solid circular shaft fixed at one end and free at the other end with a concentrated…

A:

Q: e pins are 1 cm in diameter and are made of 304 stainless steel. A distributed load of 200 N/m is…

A: Given:- two rigid bars with a 5cm x 5cm section A-36 steel. the pins are 1 cm in diameter a 304…

Q: (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a…

A:

Q: An elastic panel A fits into the rigid socket B of height h (Young’s modulus E, Poisson’s ratio ν).…

A: Strain: The ratio of change in dimension of the member due to the application of force to the…

Q: The rigid beam AB is loaded with two forces each 31 kN and the 30-mm-in-diameter and…

A: Given:- P=31kNd=20mmL=1.25mDC=3.881mTo find:-Angle in rad by which rigid beam AB will rotate

Q: The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube…

A:

Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…

A:

Q: The thin-walled tube is used as a beam to support the uniformly distributed load of intensity wo as…

A: For the given beam and cross-section,  the maximum load w0 for allowable bending stress of 1000…

Q: The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 15 mm is subjected…

A:

Q: Sketch Mohr circle for the shown element. Use Mohr Circle to determine the normal stresses On and Ot…

A: We have to find the value of normal stresses and shear stress and orientation of principal stresses…

Q: The solid steel rod (1) shown in the figure has an allowable shear stress of 18 ksi. The brass tube…

A: Given : Allowable shear stress of brass tube = 6 ksi Allowable shear stress of solid steel rod = 18…

Q: A hollow steel shaft with an outside diameter of 120 mm and a wall thickness of 10 mm is subjected…

A:

Q: A square bar AB with an allowable stress of 32 MPa is attached to a hollow tube BC. Compute the…

A: Crossection of Ab = 50mm x 50mm Hollow section with outer dimater = 50mm Load on the Ab and Bc…

Q: A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of…

A: 2 mm thick tube is given as shown in the figure, shearing torque is also given and it has been asked…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.