have would could he would were If I were rich, I - travel around the world If he worked hard, he - have more money If speak perfect english, I would not teach in this .classroom what would you do if a stranger - - you a one million

Q: A positive moment diagram of the real beam when loaded to a corresponding conjugate beam is directed…

A: The given statement is true.

Q: which of the following distance where the cost of earth works is the same

A: earthwork is used in the construction of highway pavement

Q: Road Width = 10 meters %3D Fill Slope 2H:1V while Cut Clope 1H:1V %3D %3D If the Cross-section notes…

A:

Q: Manufactured scaffold planking with spans greater than 10 feet in length must be labeled to indicate…

A: According to the General Requirements of Scaffolding, Part b (1): "Each scaffold shall be designed…

Q: 1. For the beam show below, draw its shear and moment diagram and determine its maximum bending…

A:

Q: 2. At 1:00 pm, a thermometer reading 90°F is taken outside where the air temperature is 15°F. At…

A: Given data, Room temperature T0 = 90oF Outside temperature Ts = 15oF

Q: (c) Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks after…

A: Data Given: Bulks after excavation = 10% Shrink = 12% Chainage distance = 100m Asked: Draw Mass…

Q: Question 2 For the storm shown in Question 1, estimate the spatial average rainfall for this storm…

A: Isohyets(mm) Area(km2) Station-0 0.88 0-10 1.59 10-20 2.24 20-30 3.01 30-40 1.22 40-50…

Q: The cantilever beam is loaded as shown in the figure. Derive the equations for the shear force (V)…

A: Shear equation:Vx=-4x       0<x<8'Vx=-48=-32k       8'<x<16'Mx=-2x2…

Q: Use the graphical method to construct the shear-force and bending-mom diagrams for the beam shown.…

A:

Q: If the link AB have a constant angular velocity of MAB D 30 rad/s clockwise. Determine whe- 0-35°:…

A: angle = 35 degree angular velocity of AB = 30 rad/ s

Q: Give the data of a project as follows: Task Predecessors Duration Manpowers /week Draw the…

A: PERT is a strategy utilized for ventures where the time required or expected to finish various…

Q: B) Cork is used as for sealing sparkling wine bottles. Aside from friction, why not use rubber to…

A:

Q: PROBLEM 1 or the truss shown in SD-001, The strength of the truss is assumed to be governed by the…

A:

Q: Determine the design tensıle strength (LRFD) of an ASTM A992 W8x24 with four lines of 4-in. diameter…

A: Tensile strength is the dimension of the amount of force acting on a particle to pull.  LFRD is to…

Q: 1- Determine the reactions at the supports and draw the moment diagram of the statically…

A:

Q: A town has an existing horizontal sedimentation flow tank with an overflow rate of 17 m³/day/m², and…

A:

Q: Problem I. A steel beam cross section is assembled as shown by bolting the channel, C200 x 27.9,…

A:

Q: If you found a purse, it to the teacher?

A: 1. if you found a purse, ---------------- it to the teacher. Answer option 4 : Would you give if you…

Q: The safe stopping sight distance for a design speed of 55 kmph on two way traffic with single lane…

A: Given- Design speed V=55 kmph, Two way traffic with single lane road, Longitudinal friction f=0.36,…

Q: A 5 cm diameter shaft is reduced to a diameter of 2.5 cm and subjected to a torque of 200 N-m. It is…

A: Solution: Given Data: Diameter of the shaft, D= cmChange in diameter, δd=2.5 cmTorque, T=200…

Q: Question 9 Both the novel and the movie the same mysterious ending. A) have B) has c) haves Question…

A: Question 9  Option A Both the novel and the movie have the same mysterious ending.

Q: explain in detail duty and delta of a crop; what’s their relationship

A:

Q: PROBLEM 2: The 280-kg, 6m-wide rectangular gate shown is hinged at B and leans against the floor at…

A:

Q: During a theodolite traverse, the following observations were made in the field: Calculate the…

A:

Q: 1 a.) V 3 Tiok A 9' B Find the reactions. Draw and label the V and M diagrams. Fill in the blanks.…

A:

Q: 5. For several measurements of a required distance, the most probable value is 546.75 m. If +/-0.15…

A:

Q: Wheat is to be grown in certain place, the climatic conditions of which are tabulated below,…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: F=kx=k(1) k=? *k is Flexural stiffness

A: Given, F = KxF = K

Q: PROBLEM 2 The table lamp consists of two uniform arms, each weighing 4 N and lengths of 600 mm and a…

A:

Q: A hole 12 mm diameter is to be punched. through a plate 18 mm thick. If the shear strength of the…

A: Diameter of hole (D) = 12mm Thickness of plate (t) = 18mm Shear strength of material (Su) = 300…

Q: Design rapid mix basins by computing the following: a) Tank volume if tank height is 1.0m and tank…

A: Height of the tank=1.0m Diameter of the tank=0.75m Flow rate is=0.44m3/s

Q: rod. Answer: PA = 239 kN B A 6 m 6 m 5 m 4 m +2 m→ 600 kN

A:

Q: Graph origin Variable A For the following fictional expressions, determine the type of expression…

A: This is not a linear graph . As it is clearly understood because in linear graph , variable A and…

Q: In fluid flow, it is assumed that the fluid's density is constant throughout the system. True or…

A: In Fluid mechanics, the density is assumed to be constant through the flow this flow is called…

Q: A tension member with Pu3225 k is to consist of a pair of angles with a 3/8-in gusset plate between…

A: Question is based on the tension member consist of pair of angle . Load on the member and thickness…

Q: 7. TRAPEZOIDAL RULE. A series of perpendicular offsets were from a base 1iné to a curved boundary…

A: Using trapezoidal formula to find area enclosed by offset