has high precision value, then the standard deviation for the measurements will be Zero O will not be affected O High O Low O

Q: Choose correct option Q21/80 Which register is the slowest one OPTIONS SIPO PIPO SISO PISO

A: While PIPO shift register is the fastest one, the slowest shift register is SISO.

Q: Draw the signal for C, D, and E on the timing diagram below. Initial condition, C=0, D=1, E=1.

A: In the given circuit the output waveform of the JK flipflop and the SR flipflop needs to be obtained…

Q: A OR 1 makes O A O 1 A'

A: There is no need of given data

Q: convert 128 from Hex to Octal converter

A: First we will convert Given hexa decimal number into decimal number and than we will convert decimal…

Q: In a DIA converter, LSB represents 0.2 V. The digital input is (0111) will cause an analog output of…

A:

Q: Refer to Figure below. For midpoint biasing, lp would be + 20 V Vin # 0.1 µF 7.5 mA 10 mA. 2.5 mA 5…

A: We need to find out mod point biasing current for given circuit

Q: The standard error of the mean of the following set of readings is equal to

A: Given Dataset  100, 109, 98, 102, 96, 95

Q: Q) In deflection type of pressure gauge, the out put can have an * . infinite number of value F T O

A:

Q: The signal is sampled with sampling time interval of 5 seconds then the time period of the message…

A: The sampling frequency should be at least twice the message signal frequency. fs≥2fm The sampling…

Q: Which one of the following is the correct implementation of this multiplexer?

A:

Q: Systematic errors are reading error O instrument calibration O unsuitable environment all of these O…

A: The explanation is as follows.

Q: The given system has accuracy.

A: We need to tell about accuracy of given system.

Q: if the Johnson counter start with sequence 1010 what is the output after three clock pulses 1100…

A: The given input sequence is 1010. The johnson counter is a shift register with its input data as the…

Q: The forbidden energy gap E, in the case of germanium semiconductors is approximately O 6ev O 5 ev O…

A: Given: The forbidden energy gap Eg in case of germanium semiconductor is approximately ______.

Q: mov a,#01h                               mov r0,#02h                               inc r0…

A: The explanation to this program is as follows.

Q: (a) Find . X (b) Find . X A B

A: Solve both parts of the question.These questions from control system topic related to Block diagram…

Q: The demand factor is always O Equal to one Less than one Equal to two O More than one

A: We need to tell about the demand factor.

Q: Determine the output waveform Q if the CLK signal is connected to EN of LATCH type D

A: The output of the D flipflop is the same as the input during the clock enable. The state of the…

Q: Any instrument should be calibrated against another instrument of 1)higher accuracy 2) lower…

A: Given  Any instrument should be calibrated against another instrument of

Q: For a JFET, the value of VGs at which Ip becomes zero is the

A: In this question we need to answer For a JFET, the value of VGs at which In becomes zero is

Q: Which of the following is true about acceptable Percent Errors?

A: The solution is given below

Q: | technique will be used to write on a special paper.

A: The impact printing technique will be used to write on a special paper.

Q: B E G C – F A (b). Identify the hazard and modify the circuit to eliminate the hazard.

A: We must add an AND gate before the output G. This will enable us to get an output of 1 called high…

Q: For the above input signals on T, please state the value of Q for each of the eight clock ticks.…

A: It is given that:

Q: 10 A strain gauge resistance with a range of 30 Ohms to 3000 Ohms is to be measured. The best bridge…

A: There are many bridges that are used to measure different elements, such that Hay's bridge is used…

Q: In CRO, the time/cm knob indicates scale on vertical axis. Select one: O True O False

A: A cathode-ray oscilloscope (CRO) is a type of electrical instrument which is used for showing the…

Q: Find the relative static error when the true value of a resistor is 100 Q, while its measured value…

A: Given, True value of resistor, Rt=100 Ω Measured value of resistor, Rm=105 Ω

Q: A full-wave rectifier allows unidirectional current through the load during degree of the input…

A: Full wave rectifier is a device that converts the ac supply at the input into dc output. For the…

Q: The reverse current in a diode is of the order of O KA mA O A O μA

A:

Q: 1. What does it mean to be 80% calibrated? 2. What it perfect calibration? 3. How does calibration…

A: Introduction Calibration is significant because it aids in the accuracy of measurements, which is…

Q: Which of the following element is used to transmit the measured value from one place to another

A: The element which is used to transmit the measured value from one place to another place is Signal…

Q: a. Inverse DFT or X(k) for 0

A: IDFT or DFT is used for the application of signal process which access the signal on different nodes…

Q: JFET is a unipolar device and current-controlled device current-controlled device unipolar device…

A:

Q: O Buld acrenit to perform (3 dt 3

A:

Q: Q) In deflection type of pressure gauge, the output can have an infinite number of value of output.

A:

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.