hafts are of same length and same material. The diameter and maximum shear s second shaft is twice that of the first shaft. Then what is the ratio of power develo en the first and second shaft?

Q: 3K/ft 12K IGK 16K 2K/ft a to tatat 8' 4' 4' 4! 4' 8'

A:

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A:

Q: The bearings at A and B exert only x and z components of force on the steel shaft. a) Draw shear,…

A: a.

Q: Engr. Mercado wishes to replace a solid transmission shaft 4.2 inches with a hollow shaft of same…

A:

Q: a)Draw shear force and moment diagrams. b)Draw the shear stress distribution that will occur in the…

A:

Q: ven the stress tensor Го 0. 0 200 0 0. 0. 0. Determine the normal stress on plane ABC whose normal…

A:

Q: BD bar is 50mm wide and 15mm thick. All pins are 12 mm in diameter and have a one-sided cutting…

A: Given data as per the question Width of bar  BD =50 mm The thickness of bar  BD =15 mm The diameter…

Q: Q1 /Draw S.F.D and B.M.D 20 N/m 100 m 3m 1m 6m Gm Shear Force Diagram S.F.D B.M.D

A: Given Data The UVL acting on the beam is: 50 kN/m The UDL acting on the beam is: 20 kN/m The…

Q: 1. A 100 mm diameter shaft is subjected to a torque of 6 KN.m and a bending moment of 2.5 KN.m. Find…

A:

Q: A material is made in square cross section of side 1 cm. When 2kN force applied on the material.…

A: given square cross section of side (S)=1 cm                                           s = 10mm…

Q: The Shaft Shown is ma de from steel Pipe branze core. 1ut side radius = 30 mm inside Radins- 15 Mm…

A:

Q: A 3 m- B- 4 kN/m

A:

Q: Find wark done F = 2.221N d=1-22m

A: Given data : Force=F Displacement=d   Required : Work done

Q: Find the volume of the wheel. Assume IPS units. Hold Ctrl and scroll on your mouse to zoom in on the…

A: Given Data A=6.99 B=0.52 Find Find the volume of the wheel.

Q: EXERCISES 1. A shaft running at 400 rp.m. transmits 10 kW. Assuming allowable shear stress in shaft…

A:

Q: 6. A propeller shaft in a ship is 350 mm in diameter. The allowable working stress in shear is 50…

A:

Q: A state of stress at a point A is given by ox = 50 MPa, oy = -25 MPa, and txy = -100 MPa. What is…

A: Please see the below explanation;

Q: ction shown Assu

A: Given:  T = 4730 KNm τ = 125MPat = 10mm

Q: Draw the shear force and bending moment diagrams for each of the diagram.

A:

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A:

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A: Given data, DAC = Diameter of AC segment = 50 mm DCB = Diameter of CB segment = 100 mm TD = Torque…

Q: Q2) A hollow shaft is required to transmit 600 kW at 110 r.p.m., the maximum torque being 20%…

A: Step 1: Step 2: Step 3: Step 4:

Q: Question 1 Pulleys A and B with the dimension of 66 mm in diameter are connected to solid shafts AB…

A:

Q: A single cylinder engine operating at 1,500 rpm develops a torque of 10 N- m. The Friction power of…

A: Given:N=1500 rpmT=10 N.mFP=0.5 kW

Q: = Draw the shear and bending moment diagram, where p 8 kip.

A:

Q: If allowable shear stress in the shaft is 80N/mm? and the torque equivalent(Te) is 1.23 x106 N-mm.…

A:

Q: S2) The allowable shear stress limit value of the steel from which the stepped shaft is manufactured…

A:

Q: a unity. If you know that diameter of bolts 10 mm and it's allowable shear stress is 26 kN/m

A: FREE BODY DIAGRAM-   ΣMA=012×26×4×83-RB×8=0RB=17.333KNΣFY=0RA+17.3333-12×26×4=0RA=34.6667KN So that…

Q: Find the allowance.

A: Shaft:

Q: 1.5 in. 90 lb/ft 0.75 in. 800 lb. 3 ft. 3 ft. 6 ft. 4 ft.

A:

Q: Find the. Force

A: Given  The magnitude of Force F1= 1000 N                                        F2=880 N

Q: 1. Write the shear and moment equations and draw the shear and moment diagram. 50 kN/m 100 KN 20…

A:

Q: cal culate and draw s hear and M oment diagram 4kル 2kル DM V 2 m TRB RAP

A: Consider vertically upward force & CW moment as (+)ve and vertically downward force & CCW…

Q: From 3 forces, 2 bending moments and 1 toque acting on B, which ones are non zero, and the direction…

A: free body diagram

Q: Find the diameter of the propeller shaft, which has to transmit power of 1.5 kW at 8 Hz without…

A:

Q: A motor applies 360 lb-ft of torque which is transferred through gears to shaft BD. At gear C the…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: A circular shaft of 40 mm diameter is required to transmit torque from one shaft to another. Find…

A: Diameter of the circular shaft d=40 mmShear stress To Find-The value of the safe torque T.

Q: Determine the vertical displacement of joint C . EA is constant

A: The vertical displacement of the joint C. FBD: The free-body diagram of the joint C is shown below.

Q: A solid shaft with a diameter of 20 mm is shown below. The shaft is fixed at points A and B. In the…

A: As per given question question a) Draw a torque diagram for this shaft. b) Determine the maximum…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.