H.W.21 A load of P = 100 kN is supported by a structure consist- ing of rigid bar ABC, two identical solid bronze [E = 100 GPa] rods, and a solid steel [E = 200 GPa] rod as shown in Figure Each of the bronze rods (1) has a diameter of 20 mm and is symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 24 mm. All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the bolted connection at B. Determine (a) the normal stresses in the bronze and steel rods. (b) the downward deflection of rigid bar ABC. (1) (1) 3.0 m 1.5 m B

H.W.21 A load of P = 100 kN is supported by a structure consist- ing of rigid bar ABC, two identical solid bronze [E = 100 GPa] rods, and a solid steel [E = 200 GPa] rod as shown in Figure Each of the bronze rods (1) has a diameter of 20 mm and is symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 24 mm. All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the bolted connection at B. Determine (a) the normal stresses in the bronze and steel rods. (b) the downward deflection of rigid bar ABC. (1) (1) 3.0 m 1.5 m B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer clearly with free body diagram don't waste my question I will vote it up for your effort thanks.
need in 5 minutes i will upvote!
7 ft 5 ft The assembly shown above includes column AB, which has the following properties: Pinned (top and bottom) for buckling about x-axis Free at top and fixed at bottom for buckling about y-axis Circular cross-section with 8-inch diameter E = 10000 ksi Which of the following is closest to the critical buckling force of column AB? O Per = 269 kip O Per = 1080 kip O Per = 538 kip O Per = 135 kip
A steel bar of a length, diameter and Young's modulus of 400 mm, 20 mm and 20 GPa is placed concentrically within a brass tube which has an outside diameter, thickness, length and Young's modulus of 30 mm, 4 mm, 400 mm long and 100 GPa respectively. The compound bar hangs vertically with it's upper end rigidly fixed with a collar fitted to the bottom end. The application of a load P results in the compound bar storing a total of 7 J of energy. Calculate : 1, 1)The gradually applied load 1,2)The suddenly applied load 1,3)The impact load that fails 150 mm and induces 7 J of energy 1,4)The instantaneous stresses in both materials 1,5)The instantaneous elongation of the compound rod.
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A
Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is welded to tube AB via plate B. The cross-section area of the tube is equal to 1100 mm2 and the diameter of the rod is equal to 15 mm. calculate the axial deformation of point C? (Esteel=200GPa and EAl=70GPa)
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.5 in.². Assume lengths of a = 40 in., b = 68 in., c = 28 in., L₁ = 55 in., and L2 = 100 in. The normal stress in bars (1) and (2) must be limited to 48 ksi. Determine the maximum load P that may be applied to the rigid bar. Answer: Pmax= i L₁ a (1) B Rigid bar b ܕܐ kips D
The horizontal beam ABC shown in thefigure is supported by columns BD and CE. Thebeam is prevented from moving horizontally bythe pin support at end A. Each column is pinned atits upper end to the beam, but at the lower ends, supportD is a sliding support and support E is pinned.Both columns are solid steel bars (E = 30 x 106 psi)of square cross section with width equal to 0.625 in.A load Q acts at distance a from column BD.(a) If the distance a = 12 in., what is the criticalvalue Qcr of the load?(b) If the distance a can be varied between 0 and40 in., what is the maximum possible value ofQcr? What is the corresponding value of thedistance a?
The rigid bar BCE is supported by two links AB and CD as shown in Figure 1. The Link AB is made of aluminum (E = 70 GPa) and the link CD is made of steel (E = 200 GPa). Both links have a Width= 35 mm x thickness= 7 mm rectangular cross-section. Each of the four pins A, B, C and D has a 5 mm diameter. For the 30 kN force at point E,
Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A and roller supported at location B. A uniformly distributed load of 40 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end C. 20 kN 40 kN/m В. 8 m 3 m