Answered: 8. Calculate the horizontal reaction at…

8. Calculate the horizontal reaction at O in Fig Q8 due to the load P = 177 N applied to the bar OB. The dimensions a, b, c and d are 229, 63, 52 and 68 mm respectively. (Answer in N) Fig Q8 A P C B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.19P: Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements...

See similar textbooks

Related questions

Q: 嗎! 可 CCC

A: The image depicts an ancient Egyptian scene, likely illustrating some form of craft or technological…

Q: But there is no 2 & 4 option to the multiple choice

A: Explanation: The interior of the semi circular log is made hollow so definitely center of gravity…

Q: When should a percent sign (%) be used with the LIKE operator?

A: Like operator: The like operator are likely to used in where clause to find a special kind of…

Q: How much do you save each week if you drove a prius instead of a pickup truck? Assume you drive 125…

Q: Processing times (including setup times) and due dates for six jobs waiting to be processed at a…

Q: where did you get 0.157

A: Given:Figure with dimension is providedTo find:Percent reductions in areaPercent reduction in area…

Q: How did you find the value of Patm of value 101.325?

A: How did you find the value of Patm =101.325 kPa?

Q: can tutor continue the next two questions also

Q: can tutor explain the what is all of the equations means and also answer the next 2 questions

A: To solve the physics problems, let's break them down one by one:1) Calculate the force experienced…

Q: I need these 3 parts answered for a review activity.

A: The basic symbol for surface texture is given below. The readings can be given either in micrometer,…

Q: Subparts 1, 2, and 3.

Q: I'm sorry instead of 695 it was 605.

Question

Help with the question

8. Calculate the horizontal reaction at O in Fig Q8 due to the load P = 177 N applied to the bar OB. The dimensions a, b, c and
d are 229, 63, 52 and 68 mm respectively. (Answer in N)
A
a
Fig Q8
b

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")
Need Solution through half hr please
Please solve the following problem following the steps highlighted
The figure shows a vehicle jack. In the operating range, a force analysis is required when 0 = 26°. The rectangular bars are all the same with L= 350 mm length, w = 10 mm width and b = 5 mm thickness. Note that bars are designed pinned ends for buckling in the front plane. Calculate the maximum force F (in Newton) for buckling condition only in front plane (parallel to plane ABC), knowing that: Compressive stress yield strength, Sy = 290 MPa Modulus of elasticity, E = 207000 MPa Safety factor n = 3.0 A F b L x 0 Во Front view plane
I hope the tutor can write the steps clearly and beautifully.
2. The figure shows a spring chair. The chair weight is 100 N. The spring free-length is 500 mm, mean diameter is 200 mm, wire diameter is 10 mm and number of turns is 12. The spring wire material is Music wire A228 with modulus of rigidity of 82700 MPa. Calculate the initial deflection of the spring under the chair weight. If a child seats on the chair, calculate his weight to bush the spring to the shut height. Calculate the stresses in the spring at that condition. BFD'N y = d*G 8FD T = K, 4C +2 K = 4C – 3 D C = --- o00000000od
Need correct answer only