H.W.1: A rectangular beam with dimension of (250*635) mm and d = 584 mm, f 28 MPa and fy = 400 MPa. Check the state of the section and determine the stress caused by the bending moment, M = 61 kN.m. As=1516 mm² 250 mm 584 mm 51 mm

H.W.1: A rectangular beam with dimension of (250*635) mm and d = 584 mm, f 28 MPa and fy = 400 MPa. Check the state of the section and determine the stress caused by the bending moment, M = 61 kN.m. As=1516 mm² 250 mm 584 mm 51 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the beam and loading shown, consider section n-n and determine the shearing stress at a) point…

A: Given data : We are asked to determine the shearing stress at A ) Point a B ) Point B

Q: Determine the design strength of the beam shown. Assume fy=345MPA and fc=21MP.. 3-22 mm 75 375 mm…

A: We have to determine the value of design strength of the beam shown as per the given data in the…

Q: For the same beam and loading case in Figure Q1, where within the cross-section will there always be…

Q: The box beam is made by nailing four 2- in. by 8-in. planks together as shown. (a) Show that the…

Q: Using Method of Joints, determine the force in BC below. Using Method of Sections, determine the…

A: Calculate the angle α from the given figure.

Q: Q.No.3: Determine the ACI design moment capacity =60000 psi. Also draw the strain diagram? 4 #9 bars…

Q: alculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained…

A: given-a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28…

Q: MPa, Clear cover= 40 1.What is the flexural capacity of the beam at face of the support KNm? 2. What…

Q: 13.A rectangular beam has b = 300 mm and d = 410 mm. The beam is used to carry a factored moment of…

Q: Analyze the Shear Capacity of the Steel Section. a.) W24 x 94, Fy =345 MPa

A: ASKED: To determine the shear capacity of the given steel section. Given, Steel section: W24×94…

Q: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20…

A: Given, b=d2fc=9 MPafs=124 MPan=11φ=20 mm

Q: A simply supported beam is subjected to two point loads, each P = 340 lb, as shown in the figure..…

Q: Determine the design moment strength (Mu = (pMn) of the rectangular section shown in Figure. Given:…

A: Given Data: fc'=4 ksi fy=60 ksi As=4.5 in2 d=21.5 in b=13 in

Q: 30 mm y = C 30 mm b An aluminum strut has a cross section referred to as a deep hat. Locate the…

A: Given data a = 70 mm b = 115 mm Thickness = 12mm

Q: The dimensions of a rectangular beam = 770 mm. SIT D. are limited to b = 300 mm and h %3! Assume…

A: Note - answer for tension reinforcement area should be 3839mm2.

Q: d 9.09

Q: The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm.…

Q: A rectangular beam with notches and a hole (seefigure) has dimensions h = 5.5 in., h1 = 5 in., and…

A: Given:- h=5.5in h1=5in b=1.6in M =130 kip-in σmax = 42,000 psi To find:- (a) What is the smallest…

Q: Determine the vertical displacement of joint A. Each made of steel and has a cross-sectional area of…

A: First theorem of the castigliano- In any beam or truss subjected to any load system, the deflection…

Q: APIENT 2. Use the method of sections to determine the forces in members AB, FG, AH, and GH. 3 ni…

Q: Two steel plates are welded together to form an inverted T-beam and are loaded as shown below.…

A: We know that Bending stress is given by σ = MI*y For Maximum bending stress we can write σmax =…

Q: Assume that the sections have cracked, compute the bending stresses in the concrete and steel for…

Q: Determine the design moment capacity of the beam with the following sections properties. Given: d…

Q: A rigid bar AB' and "CD as shown are supported by pins at "A" & "C" and two ross. Determine the…

Q: A rectangular beam has b = 300 mm and d = 410 mm. The beam is used to carry a factored moment of 24…

Q: Asimply supported wood beam that is 13.5 m long carries a 36 kN concentrated load at B. The…

A: Given, Length of the beam = 13.5m Load = 36KN OUR AIM IS TO DETERMINE THE FOLLOWING: 1.shear stress…

Q: 2. Find the support reactions at D and the tension forces in AC and AB. The beam has a mass of 100…

A: As their are two questions, the first one is solved. Calculating the horizontal and vertical…

Q: 15. Refer to figure 6. Determine the elongation of the A-36 steel (E = 200 GPa) member when it is…

A: Consider Half of beam then length =L=0.5 m=500 mmand width B1=20 mm and B2=75 mmload P=200 KN=200…

Q: 1500 kN (3 4 3 A 8 cm 771

A: To find force in member CD

Q: Situation 1| Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section…

Q: E 250 mm P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA,…

A: E=2G(1+μ) GIVEN E=205GPa G=82GPa by formula 205=2X82 (1+μ) μ=1.25-1=.25

Q: marks) 0.4 m B Mass2=35kg Mass1=65 kg 0.32 m 0.16 m 0.16 m

Q: Part 2 A Pratt roof truss is loaded as shown. Using the method of joints and the method of sections,…

A: Solution truss analysis by using method of joint

Q: A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement…

A: Given: The width of the beam is 280 mm. The effective depth is 500 mm. The area of reinforcement is…

Q: The cross-section of member AB is a 0.45in by 0.45in square. Determine the shear stress at section…

Q: Using the method of joints, determine the internal forces in each member of the truss. Show your…

A: Compute the support reactions using the equilibrium condition:

Q: Channel sections are used as a purlin. The top chords of the truss are sloped at 6H to 1V. Trusses…

A: Given, Dead load=600 Pa Live load=800 Pa Wind load=1300 Pa Windward=0.5 Leeward=0.4 Fbx=Fby=248 MPa

Q: Design the beam wooden section of a simple span with 3.5 m in length. Use the given allowable stress…

A: bending stress theory used with some assumption. isotropic , homogeneous and elastic material is…

Q: A horizontal beam AD is supported by an inclined strut BC carries a load W = 2.4KN at the position…

Q: 2. For the truss shown below, determine the forces in members UP, QL, JK. Assign a negative value…

A: The section is given, cut the section vertically between T and U: Calculating the support reaction:…

Q: The A-36 steel bar AB has a square cross section. Figure 1.5 in. 30 10 ft <1 of 1 1.5 in. +H 1.5 in.…

Q: A = 0.5 in.? 3 ft OD | 20 kips 2 ft 2 ft -→ 4 ft 4 ft A = 0.75 in.²

Q: 136° 0 395 B Answer: Foc i 108 1- Dimensions in millimeters

Q: 25N/m P A 1m 1m Ay = 27N Rg = 15N

A: To determine force P and value of x, we have to use the equilibrium equations. Freebody diagram is…

Question

H.W.1: A rectangular beam with dimension of (250*635) mm and d = 584 mm, f' =
28 MPa and fy = 400 MPa. Check the state of the section and determine the stress
caused by the bending moment, M = 61 kN.m.
As=1516 mm²
250 mm
584 mm
51 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the loading. Forces are positive if in tension, negative if in compression. Answers: AB= i AH = i CD = ܠܚܕܠܚ ܘ ܚ BC = i BH = i CF = 4.6 m DF = i CG= i CH = i GH = i DE = i i EF = i FG = i i B 3.3 m H 22 KN 4.6 m 4.6 m 4.6 m G D 60 KN F 22 KN kN kN kN kN kN kN kN kN kN kN KN kN kN E
Solve the problem with complete and neat solution. Draw the figure. Determine the forces in members IH, KC, and BC of the truss using method of sections. State whether each member is in tension or compression. 60KN A 3m B 3m K H 4m C 3m 60KN D 3m F E
6-49. Determine the maximum tensile and compressive bending stress in the beam if it is subjected to a moment of M = 4 kip. ft. 【0.5 in.¯µ| |-—3`in. 0.5 in. 3 in. 10 in. C D -0.5 in. B M 0.5 in.
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. Ad Answers: AB= AG= BG= BC= i CD= CF= CG= DE= B i EF= DF= i i FG= i G 2.0 KN C F 7.8 KN D KN KN KN KN KN KN KN KN KN KN KN
A built-upsection is to be used as a girder. It is simply supported over a span of 9 meters and laterally supported at supports and midspan. Use Fy=345MPa and Cb=1.0 Properties of the section: A=12,620mm2 d=450 mm tw=10 mm bf=300mm tf=14mm rx=203.88mm ry=70.67 mm Ix=524.59x106mm4 a.Determine the elastic section modulus, Sx. b.Determine the plastic section modulus, Zx. c.Determine the compactness of the section. d.Determine the lateral support condition. e.Determine the Allowable Flexural Strength of the girder. f.Determine the Ultimate Flexural Strength of the girder.
A wooden beam is fabricated by nailing together three pieces of dimension lumber as shown. The cross-sectional dimensions of the beam are also shown. The centroid is 3.4 in. below the top surface of the beam, and the moment of inertia about the z axis is 230.9 in.4. The beam must support an internal shear force of V = 365 Ib. If each nail can provide 120 Ib of horizontal resistance, determine the maximum spacing sfor the nails. 2 in. 4 in. 2 in. 2 in. 8 in. O 4.86 in. 8.32 in. O 7.91 in. 9.36 in. O 5.59 in.
Using the method of sections, determine the force in members BD, DE and DF. D 1 m F 20 kN В 1 m A C G H E 1.5 m 1.5 m 1.5 m 1.5 m 40 kN 40 kN
The beam is made from four boards nailed together as shown below. If the nails can each support a shear force of 500 N, determine their required spacing s' and s if the beam is subjected to a shear of V = 3.5 KN. 25 mm 250 mm 250 aut BE 40 mm 25 mm 25 mm 50 mx
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)
Hinge W B C D E Hinge 0.47 m 0.47 m 0.47 m 0.47 m 23 mm 14.7 mm A central beam BD is joined at hinges to two cantilever beams AB and DE. All beams have the cross section shown. For the loading shown, determine the largest w so that the deflection at C does not exceed 2.1 mm. Use E = 200 GPa.
Problem 2: Determine the forces in all diagonal and horizontal members of the truss shown below using the method of sections. Determine the force in all vertical members using the method of joints. Hint, the structure is symmetric. The distributed load is transferred to the truss from the roof purlins. State whether the members are tension or compression. Summarize your results on a sketch of the truss. 2.5 k/ft H M K 12 ft A G B C D F 6 @ 12 ft = 72 ft
Determine the shear stress in plane AB of the beam section shown if it is subjected to a shear force V. Assume that the neutral axis passes through the A-B axis. Usar los siguientes datos: H1 = 15 in. H2 = 20 in. H3 = 8 in. W = 22 in. H2 H3 V = 300 Kips H1