H.W. 2: What is the total active force/unit width of wall and what is the location of the resultant for the system shown in Fig.? Use the Coulomb equations and take a smooth wall so S=0° 7.0 m 9-100 kPX ABANS - 32° <-165 EN³ SHV 7-19.25 Sol 1 Sall 1 30.3 kPa 14 107.5 EN 131 EN T 13.7 171 R=40.6LN IN

H.W. 2: What is the total active force/unit width of wall and what is the location of the resultant for the system shown in Fig.? Use the Coulomb equations and take a smooth wall so S=0° 7.0 m 9-100 kPX ABANS - 32° <-165 EN³ SHV 7-19.25 Sol 1 Sall 1 30.3 kPa 14 107.5 EN 131 EN T 13.7 171 R=40.6LN IN

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter12: Lateral Earth Pressure

Section: Chapter Questions

Problem 12.8P

See similar textbooks

Similar questions

-2 ft 10 kip 4 in. B B 1.5 ft-- 4 in. 6 in. ● 4 kip 0.5 ft 2 ft- - Change the magnitude of 10 kip to 7.9 kip - Change the outer width of the cross section from 6 in to 8 in - Keep the wall thickness 1 in (example, instead of 4 inches, the inner width of the cross section is equal to the outer width minus 2 inches). - Determine the maximum in-plane shear stress in the box beam at point A. Show the results on an element located at this point - Determine the principal stresses in the box beam at point B. Show the results on an element located at this point
A beam made of multi-layered material is fixed to the wall as shown. Determine the position of layer (y=?) which fails due to applied transverse load V. (where is the maximum shearing stress?) wall y h h b
A 150 mm diameter rivet resists a shear force of V =8 kN. Find the average shear stress in the rivet. %3D 150 mm (A) 230 kPa (B) 370 kPa (C) 430 kPa (D) 450 kPa
4.144 The tube shown has a uniform wall thickness of 12 mm. For the 170110 S loading given, determine (a) the stress at points A and B, (b) the point where the neutral axis intersects line ABD. ne-601 la archy siques of bat Fig. P4.144 D F H E 28 kN 14 kN 28 KN 125 mm. 75 mm 1 A 025.0 40137
PROBLEM: The uniform 2Mg bar is supported by a smooth wall at A and by a pin at B. Determine the diameter of the smallest pin that can be used if not to exceed a shear stress of 60 MPa. 10 m
7. Determine the horizontal force P that would keep the uniform 12-kg rectangular plate in the position shown. 0.4 m 0.3 m
Member BC (Checking computations.) +1 ΣFr =0 24 1.6(15) = 0 %3D SEMB = 0 180 1.6(15)(7.5) = 0 %3D %3D PROBLEMS 1-2 Determine the axial forces, shears, and bending moments at points A and B of the structure shown. 1. 65KN 85KN 55KN 60° A B 9 m 5m- 9m- 3m 5m- 3 m
The wall thickness is 10 mm. Determine the second moments of area T., and with respect to centroidal x' and y' axes. In addition, determine the radii of gyration K., K., and K. 100 mm -200 mm -200 mm 100 mm 100 mm 100 mm X
0.2: Consider the cantilever beam subjected to the concentrated load shown below The cross section of the beam is of T-shape. Determine The shearing stress 20 mm from the top surface of the beam of a section adjacent to the supporting wall. 50 KN 120mm 2 т 20mm 120mm 20mm
The wall separates water and glycerin(p=1260kg/m^3). Considrr a unit width of the rectangular panel AB when d=2.0. Determine a) using panel equations, determine F1, the hydrostatic force acting on the gate due to water b) where is the line of action of F1 relative to point B c) determine F2, the hydrostatic force acting on the gate due to glycerine d) what is the net hydrostatic force F acting on the gate? e) where is the line of action of F relative to point B
5. Calculate the depth of neutral axis at balanced condition if the effective depth is 250 mm and fy is 415 MPa. a. 147.78 mm b. 212.50 mm c. 294.12 mm d. 223.25 mm 6. Calculate the stress at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neural axis is 100 mm. a. 800 MPa b. 500 MPa c. 1000 MPa d. 900 MPa 7. Calculate the strain at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neural axis is 100 mm. a. 0.0040 b. 0.0025 c. 0.0050 d. 0.0045 8. Calculate the depth of compression at balanced condition if the effective depth is 250 mm, β1=0.85, and fy is 415 MPa. a. 180.63 MPa b. 135.57 MPa c. 125.61 MPa d. 178.86 MPa
2.16 Suppose that glycerin (T = 20°C) is flowing and that the pressure gradient dp/dx is -1.5 kPa/m. What are the velocity and shear stress at a distance of 8 mm from the wall if the space B between the walls is 5.0 cm? What are the shear stress and velocity at the wall? The velocity distribution for viscous flow between stationary plates is %3D 1 dp (Ву — у') U = 2µ dx и Problems 2.16