Grinding wheel manufacturer has written the following information"W A 10 E 4 S 17" on the grinding wheel. Explain

Q: tarting at rest, a hydroplane accelerates at a = 0.8t for the first 10 seconds and then accelerates…

A: Given:The acceleration is The acceleration after  is

Q: A cylindrical tank is resting horizontally on the ground (the circular faces are vertical). The tank…

A: There are two types of forces that act on a circular surface: one type of force is radial force and…

Q: Solve using parallelogram and Trigonometry  please explain how

A:

Q: Certain type of steel whose Proportional limit the above theðry sing n The principal stresses were…

A:

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: 2 Major parts of the lathe 2 Types of the lathe 5 Types of lathe cutting tools 4 principal parts of…

A: given; major parts of the lathe types of the lathe types of the lathe cutting tool

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: A 190 D TAB @AB,CAB 500 mm Figure 1 B AY = The crank AB rotates with an angular velocity of WAB 3…

A:

Q: A cantilever beam is under a concentrate load P (N), the beam has a length of L (m). P L y Write a…

A: Given : To find : function for internal shear force and bending moment

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2…

A:

Q: Identify Counter-sinking operation from the following drilling operation a. Ob. C. Work stationary O…

A:

Q: My desk has a mass of 165 lbm at the Earth's surface. What is its weight in pounds force (lbf) and…

A: Given data as per the question Mass of desk on earth =165 lbm Value of g on Mars =5.5 ft/s2 mass  of…

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: We need to calculate the hydrostatic force acting on the sluice gate

Q: Identify the drilling operation in which the flat bottom drill bit is used to enlarge the existing…

A: Given Data:

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: The uniform 7.4-m pole has a mass of 280 kg and is supported as shown. Calculate the force P…

A: given : m = 280 kg L = 7.4 m μ = 0.37   NOTE : self weight mg will act at middle(Center of gravity)…

Q: 1. Three vertical rods AB, CD, and EF supports a load of 36 kN. Each of the rods AB und CD has a 200…

A: When an external force is applied to any body, the body gets deformed. This deformation is resisted…

Q: Sketch a plot that contains a lateral strain for a material undergoing a temperature change which…

A: Given : Same temperature change for 2 materials one results in elastic deformation and another…

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

A: It is asked to calculate the moment at the critical location F1 = 1600 lb F2 = 640 lb

Q: a. The value of maximum torque, Tax = 640 lb.ft 167d₂ (d₂²-d₂¹) max Tmax π 16x640×12×1.75 (1.75…

A: The Torsion equation for the circular shaft is given byWhere,T = twisting moment or torque applied…

Q: Question 13 Solve the problem. Find the work done by a force of 200 pounds acting in the direction…

A:

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True O False

A:

Q: 2. Orientation is the general term used to describe the features. O linear O most important…

A: The meaning of orientation in terms of relationship between features is to be chosen from given…

Q: 1. ABEF is a light-weighted rod supported by bearings at C and D. AH is a wire. There is a 400N…

A:

Q: 5. What is most nearly the lateral strain, en of the steel specimen shown if F,= 3000 kN, E=193 GPa,…

A: Given data : Load in X direction (FX)=3000 KNModulus of elasticity (E)=193 GPaPoissons ratio…

Q: Problem 2. Determine the maximum weight of the flowerpot that can be supported without exceeding a…

A:

Q: Find the Ixx value for the plate as shown below, where b1-d2-18 mm, d1-85 mm,b2-65mm. (ENTER ONLY…

A:

Q: b. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility= c. Number of…

A: In these drawn mechanism, we need to find the number of lower pairs (binary joints) and higher…

Q: Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool…

A: Option B is correct.

Q: correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying…

A: given:

Q: What type of geometric tolerances has no datum features? O Location O Runout O Profile O Form

A:

Q: Test-lI. Write down all the operations or step by step procedure on how to create the object below.…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.