Glven the technical description of a certain lot, complete the tables below: DIST 38.588 37.736 28.278 83.100 LINE AB BC CD DA Station A B с D BEARING N 58° 46.9' E S 57° 59.7' E S 30° 46.5' E N 73° 0' W interior < division gnerating fr. B * Express all values up to 3 decimal places. * If the value is zero just write 0. Area 1 Area 2 Total

Glven the technical description of a certain lot, complete the tables below: DIST 38.588 37.736 28.278 83.100 LINE AB BC CD DA Station A B с D BEARING N 58° 46.9' E S 57° 59.7' E S 30° 46.5' E N 73° 0' W interior < division gnerating fr. B * Express all values up to 3 decimal places. * If the value is zero just write 0. Area 1 Area 2 Total

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 5.8 0+030 4.08 0+060 7.84 0+090 7.92 0+120 6.02 0+150 4.2 0+180 7.75 Use the best method applicable. Round your answer to 3 decimal places.
Compute the volume of excavation between station 24+00, with an end area of 711 ft2, and station 25+00 with an end area of 515 ft². Answer will be in yards cubed, round to the nearest whole cubic yard. 2270 2720 61290 20430 000
STA BS HI FS IFS ELEV BM1 3.92 328.7 0+00 3.3 1+00 3.8 2+00 2.8 3+00 2.5 ΤP1 4.37 5.03 4+40 3.8 5+00 5.3 6+00 3.2 TP2 3.82 4.66 8+00 2.8 BM2 2.45
PhilSys online step.. Token to PHP Chart.. PancakeSwap Binance * Marketplace Dashb. Points C andD are located at (1, 2, 4) m and (2, -1, 1) m respectively. Determine the length of DC and the angle COD, where O is the origin of the co-ordinates. Im Next NRO 28°C Haze acer 近

Choices a. 0.05 b. 1.06 c. 1.20 d. 2.19 e. 0.38
[?] ?? = [150 −60−60 −180]➢ Determine y grafique mediante el círculo de Mohr los esfuerzos principales y lasdirecciones asociadas a estos.➢ Determinar y grafique los esfuerzos cortantes máximos.➢ Grafique los posibles planos de falla.➢ Por último, ¿cuál es el valor de la tensión tangencial máxima y en quéorientaciones tiene lugar?
End Area (ft2) Volume (yd®) Volume (yd) Net Volume (yd) Station Mass Shrinkage Total Cut Fill Cut Fill Cut Fill Diagram (12%) Fill Ordinate 0+00 400 3+00 600 152 5556 843 101 945 4611 4611 6+00 500 93 9+00 253 20 The mass ordinate at sta 6+00 is: 9.200 O 6,111 O 4,589 O -4,589
Calculate the net volume of the grid below in cubic yards using the borrow-pit method. Net volume is calculated as cut volume minus fill volume (all numbers are in ft.) Grid cell side length = 5 Design elevation = 50.00 As-Built elevation of A0: 49 As-Built elevation of A1:52 As-Built elevation of A2: 55 As-Built elevation of B0: 48 As-Built elevation of B1: 50 As-Built elevation of B2: 53 As-Built elevation of CO: 45 As-Built elevation of C1: 47 B A 0 1 2 0.23 yd³ Cut 25 yd³ Cut 25 yd³ Fill 0.23 yd³ Fill C
Refer to the below diagram and the booking sheet Question: What is the number (or word/s) which must be CP 1 2.050 entered into the levelling booking sheet that is marked as: B.M. 11 RL 0.724 OP 2 3.100 (Note, if the space should have nothing written in it please 16.235 2.785 2.565 2.480 answer NONE) Set up 1 Set upa B = NONE LEVELLING BOOKING SHEET B.S. I.S. F.S RISE FALL F = 2.050 R.L. REMARKS A B G) F. H) -2.145 2.570 2.410
1. Complete the following set of profile level notes and show the customary arithmetic check. Plot the profile (you can use a graphing paper for the plot). STA BS HI FS IFS ELEV BMa TP| 1 + 00 + 25 + 50 + 75 TP2 1.24 234.51 m 1.11 3.40 4.6 2.8 3.6 2.4 3.21 2.46 2 + 00 1.2 + 25 + 50 TP3 BM, 3.2 2.8 3.06 2.74 2.40
QUESTION 2 Glven the technical description of a certain lot, complete the tables below: DIST 40.311 38.910 37.014 51.140 LINE AB BC CD DA Station A B с D BEARING N 60° 15.3¹ E S 64° 5.6' E S 42° 29.2¹ W N 61° 38.1' W interior < division gnerating fr. * Express all values up to 3 decimal places. * If the value is zero just write 0. A Area 1 Area 2 Total * If the value is negative, include the negative sign without space in between negative sign and the number. Example: value = -37, input: -37.000 * For positive values, do not include the + sign in writing the answer. *Do not include the unit in writing the answer/s.
End of the question 10 N not the grade