Given written specifications, develop the note for a threaded fastener. With the following specifications, develop the note for this threaded fastener. The threaded fastener has: • a major diameter of 3/4 inch, • a pitch length of 0.050 inches, • a unified coarse thread form, • which has a class of fit of 2, • it is an internal thread, and has a length of thread engagement of 2 1/2 inches.

Given written specifications, develop the note for a threaded fastener. With the following specifications, develop the note for this threaded fastener. The threaded fastener has: • a major diameter of 3/4 inch, • a pitch length of 0.050 inches, • a unified coarse thread form, • which has a class of fit of 2, • it is an internal thread, and has a length of thread engagement of 2 1/2 inches.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Under what conditions are straight, or non-tapering, pipe threads used?
What is cohesiveness precisely? How is a tight connection distinguished from a loose coupling?
RB&W11 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4 diameters, 1/2 turn for bolt grips 4-8 diameters, and 2/3 turn for grips of 8-12 diameters. These recommendations are for structural steel fabrication (permanent joints), producing preloads of 100 percent of proof strength and beyond. Machinery fabricators with fatigue loadings and possible joint disassembly have much smaller turns-of-nut. The RB&W recommendation enters the nonlinear plastic deformation zone. The figure shows a cross section of a grade 25 cast-iron pressure vessel, with a torque factor K of 0.09. Use Eq. (8-27) to estimate the torque necessary to establish the desired preload given that preload F;= 14.4 kip, bolt stiffness kb = 5.21 x 106 lbf/in, number of threads N=11, and material stiffness km = 8.95 × 106 lbf/in. in-11 UNCX 2 in grade 5 finished hex head bolt in in 162 No. 25 CI Determine the torque necessary to establish the desired preload and the turn of the nut in…
M25x6-4h5h-23 describe each part
i need the answer quickly
Compute the lead angle of an M16 × 1 double thread.
In an interchangeable assembly, shafts of size -0.040 25.000-0.0100 mm mate with holes of size +0.020 25.000-0.000 mm. The maximum possible clearance in the assembly will be (a) 10 microns (b) 20 microns (c) 30 microns (d) 60microns
q5 The straight surface on either side of the screw thread is known as Flank Pitch Root Crest
A compression spring needed for a machine operation has to fit within a 1-in. diameter hole. To allow for some clearance, the outside diameter of the spring should not be larger than 0.9 in. To ensure a reasonable coil, use a spring index of 9. The spring will be repeatedly cycled from its free length of 3 in. to a length of 2 in. The solid length of the spring is 1 in. The spring should have squared ends and is to be made of music wire. (a) Determine a suitable wire diameter. (b) Determine a suitable number of coils. (c) Determine the spring rate. (d) Calculate the maximum shear stress the spring will experience during fatigue cycling. (e) Show on a stress vs. time plot how the fatigue cycling on the spring will occur. (f) If the spring is unpeened, what will be the shear endurance limit of the spring material in completely reversed cycling? (g) Can the spring survive a million fatigue cycles? Show by calculation.
Sketch and label power screw thread form (Acme thread). What is the functional difference between fastener thread forms and power-screw thread forms?
help me with number 10,12 and 13.
Why Cross-rail attachmnent is required in shaper? A - В =|三 Type your Answer here:-