Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P) inclined surface. Draw construction lines lightly and edge lines boldly. Show the lines clearly please.

Q: 2.

A:

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: 4. ㅂ 1

A:

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: The given sketch is a view of modified “Plate" one view. Sketch the 2D sketch of the below figure…

A:

Q: What is the sketch of the right face

A:

Q: Draw the isometric view of the given orthographic projection of the object?

A: According to the details in the kitchen we need to draw isometric view of the given object. I am…

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: The projectors through the traces of a line are 70 mm apart and those of ends of the line are 35 mm…

A: Projector distance between the traces = 70 mm Projector distance between ends of line = 35 mm…

Q: 3. For the objects shown in isometric below, sketch the top, front, and right side views in the…

A:

Q: Directions: Draw an isometric view of the following orthographic views. Views most be properly…

A: Draw an isometric view of the following orthographic views.Views most be properly aligned attached.…

Q: Create the 3D Model of the Shaft Holder Produce Drawings: 1. Isometric 3D Shaded 2. Detail Drawing:…

A: Given Model To find Isometric 3D Shaded Front view Top View Full Sectional Left Side view

Q: Given two Orthographic views of an object, construct an Auxiliary view of the indicated (→→)…

A: Find Construct an auxiliary view of the object.

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: Draw a perspective,isometric(with 30 angle), & oblique(with 45 amgle) view of a cube.

A: Draw a perspective,isometric(with 30° angle), & oblique(with 45° angle) view of a cube.

Q: Q1: Draw the orthographic Projections of given object. 15

A: Solution:   The orthographic projections of the given object is shown below:

Q: For the given multiview projection, draw the corresponding isometric drawing. ME DA

A: For the given multi view projection, draw the corresponding isometric drawing.

Q: 3. The distance between end projectors of a line CD which is inclined 45° to VP, is 60 mm. Point C…

A: the distance between end projector of a line CD which is inclined 45 to VP , is 60mm . point C is…

Q: Draw the orthographic Projections of given object.

A: Required orthographic views of the given isometric view are drawn on grid paper. 1 Grid = 1 Unit

Q: Define a point. Also describe projection planes like horizontal plane (H.P), & vertical plane (V.P).

A:

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: 1. Sketch the CAVALIER OBLIQUE of the given object. Use corner "A" for orientation.

A: according to the details provided in the question, we need to draw a cavalier view of the given…

Q: For the 3d object shown to the right, complete the following: a) Determine the position vector from…

A:

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P)…

A:

Q: Given the Isometric views, draw the three orthographic views below

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 unit.

Q: TOP FRONT SIDE

A: GIVEN DATA ISOMETRIC VIEW GIVEN WE HAVE TO DRAW ORTHOGRAPHIC VIEWS OF GIVEN FIGURE

Q: L. Sketch the objects shown using isometric, oblique, and one- or two-point perspective.

A: It is asked to draw isometric, oblique and one point perspective views

Q: friction t

A: FIg:FBD Fr=μN∑Fy=0N=mgcosθ∑Fx=0μN=mgsinθμmgcosθ=mgsinθμ=tanθ

Q: Shade in the surfaces that will appear in the front, top, and right side views. Estimating the…

A:

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: The plan of a point T is 35 mm above XY line and its front view is 40 mm below the XY line. Draw its…

A: Given:The distance of the plan (top view) is and it is above the XY line.The distance of the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.