Given truss shown, P50 kN. The tensile oallow140MPa, and the compressive Oallow = -85 MPa. If the truss is to support amaximum load P (as given).shear, pin at B is in single shear%3D= 140 MPa, pin at A is in doubleallowDetermine the required Area of the members AB, BC and AC ifthe Oallowable of the members is 135 MPa.- 450 mm→B(3)600 mm(1)1200 mm

Answered: Image /qna-images/answer/b681b58d-0f02-4333-80b4-d4bfdea559d4.jpg

Given truss shown, P = 50 kN. The tensile Oallow = 140 %3D MPa, and the compressive oallow = -85 MPa. If the truss is to support a maximum load P (as given). shear, pin at B is in single shear allow = 140 MPa, pin at A is in double Determine the required Area of the members AB, BC and AC if the Oallowable of the members is 135 MPa. -450 mm B

Given truss shown, P = 50 kN. The tensile Oallow = 140 %3D MPa, and the compressive oallow = -85 MPa. If the truss is to support a maximum load P (as given). shear, pin at B is in single shear allow = 140 MPa, pin at A is in double Determine the required Area of the members AB, BC and AC if the Oallowable of the members is 135 MPa. -450 mm B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

With solution
SOM 6. Show your complete solution.
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in² for all the members. Determine the deformation sustained by members CG and FG. 12 kips 14 kips 16 kips A B с 10 kips |-6R-|-6A 8 ft ļE 5 ft ——6 ft—6 ft--6 ft-
Bar FA in the pin-connected structure below is to be considered rigid and is horizontal before loads are applied to the structure. Member BC is an aluminum alloy bar with E= 75 GPa and a cross-sectional area of 1000 mm². Member DE is a steel bar with E = 200 GPa and a cross-sectional area of 500 mm². Assuming elastic behavior and adequately reinforced ends for BC and DE, determine the axial (normal) stresses in BC and DE and the deflection of point A when the 150 kN load is applied. 1.5 m 1.5 m 2.5m B 2.0 m 1.0m- 150 KN
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
help me plss. ASAP
TRUSSES: Find the stresses of the given.
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa] A 000 RA B 70kN E 4 panels at 4m 16m = G 30kN H RH 3m
1.) The truss shown is made of steel members ( E = 29 x 106 psi ). Members AB and BC have cross- sectional areas of 0.80 in² and 0.64 in? respectively. For the loading shown, determine the elongation of both members B A 25 kips 5A Kips Figure #1
In a 2D truss, a two-force member has two possible forces, they are .(select correct response) or ........ tension bending torsion compression
number 4 only p =10