Given the Truss as shown below. Using Method of Joints, determine the forces at the members AB, AE, BC, BD, BE, CD, and DE. В 4 m 2 m A E 6 m 3 m- 200 kN 100 kN

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: Find in inches the inside diameter of this water pipe for an automatic icemaker. Express the answer…

A: Given     Outside diameter, d = 1 1/4 in                                  = 1.25 in…

Q: draw the left side

A:

Q: A steel beam, of lengths a = 4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: A steel beam, of lengths a = 4 m and b = 4 m and a hollow box cross section, is supported by a hinge…

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: A Prony brake with a 12” arm is applied to an engine flywheel. At 1200 rpm, the scale registers 20…

A:

Q: Compute Ix (I sub x, in inches“, round-off to 2 decimal places) for the region shown. 4

A:

Q: What did you put in the calculator to get the box answers? Please put exactly what you put

A: The solution provided in the previous response is as follows.

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: 0 = 0° A

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: need help finding dimension x and y in the casting shown 2.80 cm 5.20 cm 6.00 cm 2.50 cm E 7.20 cm

A: Draw a diagram for the given problem.

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: An automobile tire is 65.0 cm in diameter. How fast (rpm) does the wheel turn on the axle when the…

A:

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Q: Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm A 1 cm B 0.5 cm D 6 cm E 0.75 cm F 0.75 cm 0.75…

A: Solution:

Q: Make the indicated conversion between customary and metric units of weight and mass. 17…

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Note: As per the policy, we can solve the first question from the multiple question. Please,…

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.