Show whole solution Given the network as shown in figure 2, determine the three-phase fault. Assume a prefaultvoltage of Vpu = 1.0520°. Faulted bus is as shown.叶10C MVA13 8 kVX=0 15X2=0 17X=0 0510C MVA13 8/138 KVX=0 1CX1=X2=20 OHMSX0=60 OHMS10C MVA138/13 8KVX=0 1C口10C MVA138 kVX'=0 20X2=0 21X=0 1CX=0 05

In this question we need to find a three phase fault at given fault location.

Given the network as shown in figure 2, determine the three-phase fault. Assume a prefault voltage of Vpu = 1.0520°. Faulted bus is as shown. 10C MVA 13 8 kV X=0 15 X2=0 17 X=0 05 AY 10C MVA 13 8/138 KV X=0 1C X1=X2=20 OHMS X0=60 OHMS 口 10C MVA 138/13 8KV X=0 1C 10C MVA 138 kV X'=0 20 X2=0 21 X=0 1C XN=005

Given the network as shown in figure 2, determine the three-phase fault. Assume a prefault voltage of Vpu = 1.0520°. Faulted bus is as shown. 10C MVA 13 8 kV X=0 15 X2=0 17 X=0 05 AY 10C MVA 13 8/138 KV X=0 1C X1=X2=20 OHMS X0=60 OHMS 口 10C MVA 138/13 8KV X=0 1C 10C MVA 138 kV X'=0 20 X2=0 21 X=0 1C XN=005

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.16P

See similar textbooks

Similar questions

A generator is delivering power to infinite bus during post fault condition is 1.10 p.u at a power angle of 60 degrees. What is the maximum power that can be transferred? O a. 1.0 p.u O b. 1.1 p.u O c. 0.95 p.u O d. 1.27 p.u
The sequence components of the fault current are as follows: Ipositive = j2 p.u., Inegative = - j0.5 p.u. and Izero = -j 1.5 p.u. The type of fault in the system is
A 12 MVA, 132/6.6 kV, transformer having a reactance of 0.15 pu is fed from an infinite bus. The transformer feeds two motor each 6 MVA, 6.6 kV. Each motors has a transient reactance of 0.14 pu and a subtransient reactance of 0.30 pu based on its own rating. A three phase balanced fault occurs at the terminals of one motor as shown in the figure below. Find the subtransient fault current and subtransient current in breaker. M1) 132/6.6 KV СВ 38 CB Infinite Bus M2 Fault
the slip-rings replaced by separated segments In order to generate a bidirectional Voltage true / false
A generator operating at 60 Hz delivers 1 Pu MW power. Suddenly a three phase fault takes place reducing the maximum power transferable to 0.40 pu MW whereas before the fault, this power was l.8 pu MW and after the clearance of the fault, it is l.30 pu MW Determine the critical clearing angle
In single phase power factor meter there is error due to frequency and waveforms but not in three phase power factor meter, I know the reason why?? Please elaborate properly
pls solve it before 10 min
This question is about electrical power material and I want to solve it in 20 minutes
3. Single-phase T1-transformer with a power of 500 kVA and a single-phase T2- with a power of 400 kVAtransformers are connected in parallel and load 1000 kVA with 0.8-back power factor.they are feeding. The equivalent circuit winding resistance of T1 is 0.025 b and the equivalent circuit reactance is 0.06is b. The equivalent winding resistance of T2 is 0.016 b and the equivalent circuit reactance is 0.07 b. Bothhas the same conversion ratio in the transformer.a. Draw the connection diagram given in the question. b. Obtain the power sharing expression over the parameters given in the question. c. Calculate the kVA values and power factors of the transformers.
G1 Bus 1 Bus 2 Line Bus 3 T2 Bus4 M1 j402 25 MVA Ye A 13.0 kV Xg1 =10% зо мVA 13.4/69 kV 20 MVA 66/13.2 kV 15 MVA 13.0 kV Xmi =15% 10% 10% e direct-axis subtransient reactances of the synchronous generator and otor are given above in the figure. The fault impedance (ZA) is 15.87 ohm ie generating is operating 25 MVA, 0.95 p.f. lagging, and at 10% above rate Itage when a three-phase fault occurs at bus 1. Determine each three-phase ult
powe system Q8
A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b