Given the following data of a tract of land below Adjusted Latitude Adjusted Departure Line N (+) S(-) E (+) W (-) АВ 490.71 47.27 ВС 587.12 608.89 CD 327.41 786.78 1,002.76 122.67 DE 218.32 EF 1,116.62 FA 375.01 544.64 16. Determine the following area east of a line running from F to C and calculate the length and bearing of FC.

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: 20 40 t. 20 40 30 40 20 to 30

A: Gross area of the column =area of concrete + area of reinforcementGross area of the first column…

Q: C. Put the following words related to roads, bridges and waterways (barrage, pavement, dam, curb,…

A: Roads i) Pavements ii) Curb iii) Pedestrian crossing   Bridge  i) Aqueduct  ii) Deck iii) Barrage…

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: Good structural design is more related to correct natural sense than to sets of

A:

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: What is Structural Plan?

A: A structural plan is a plan used as a framework to take up the land development or renovation of an…

Q: What do you mean by the slice action and how many slice operated dimensions are used?

A: #1What do you meant by the slice action?? A slice operation is defined as the particular filtration…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Pb. Classify trees on the basis of Strength and Structure. Provide a short description in chart…

A: Trees can be classified into two types based on strength : 1 - Endogeneous trees 2 - Exogeneous…

Q: Define scale factor?

A: The size by which the shape is reduced is called as its scale factor. It is used when we need to…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: Enumerate and explain briefly each of the steps and processes involved in iterative design…

A: Introduction- The Iterative designing concentrates on cyclical or gradual progress. If you want to…

Q: Find and define " horton equation" Show illustration.

A: To find and define Horton equation.

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: A. WATER LINES, PIPES, CONNECTIONS AND FIXTURES  B.  SEWER LINES, PIPES, CONNECTIONS AND FIXTURES…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: How are units converted using dimensional analysis?

A:

Q: In an Engineering Plan it is composed of the Following : 1. architectural Plans 2 Structurally Plans…

A: (1)Architectural plan An architectural plan or drawing is a technical drawing of a building and is…

Q: CAD system to generate the final schematic

A: Computer aided design is the technology of designing,analyzing and modifying a structure before and…

Q: Name any four shape that you can identify from the sketch

A: Any sketch such as still life, landscape etc. is prepared with the helps of basics shapes. These…

Q: show a working plan drawing that is related to civil engineering

A:

Q: 1. There are two approved ANSI systems of dimensioning on drawings when it comes to engineering…

A: The 2 types dimensioning methods are: 1. Aligned method 2. Unidirectional method.

Q: Define Minimum Dimensions

A: Brief concept introduction- Minimum Dimensions- Minimum Dimension is a very wide term and it…

Q: make me a sketch of a floor plan sized 21.5meters x 14 meters with porch, carport, living area,…

A: To draw a Floor Plan in an area of 21.5 m x 14 m To provideporchcarportliving areadining…

Q: What exactly is computer-aided design (CAD)?

A: Computer aided design is main component of design of structures in Engineering.

Q: classification of rivers

A: Classification of Rivers

Q: List the only tools needed for producing FREEHAND sketches

A: The only tools needed for producing FREEHAND sketches are listed in the following steps.

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: What is used to mark the tape lengths?

A: In surveying, tapes are used to measure distances that are level, vertical, or sloping. Tapes are…

Q: Discuss MINIMUM COVER REQUIREMENTS AND STANDARD DIMENSIONS

A: Throughout reinforced concrete, the concrete cover is indeed the shortest route between the layer of…

Q: What are the types of coordinate system? Illustrate with neat figure.

A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate.  Cartesian…

Q: Define Class 1 and 2 of cross sections

A: Class 1 cross-sections are those which can form a plastic hinge with the rotation capacity required…

Q: Using specific examples (at least 5), discuss why you will prefer using CAD software for your…

A: A technical drawing used to convey information about an object is known as an engineering drawing. A…

Q: Please encode the solution

A: given: diameter of bolt=3/4 inch, thickness of plate=5/8 inch required: to encode the solution…

Q: Please give typed answer

A: Given data:- Draw a horizontal line S60W with a length of 200m, Calculate the value of TL.

Q: Distinguish between nominal scale and ordinal scale, as well as between interval scale and ratio…

A: We have many of scales available in the Market. These are very useful in the surveying and market…

Q: Beginning ^ 2 3 4 LO 5 CO 9 8 7 3 10 10 11 12. 13 5 14 15 Identify the full name and abbreviation of…

A: To Determine: Full name and abbreviation of 8 10 15

Q: cale is considered a mall scale one of the answers ge scale ddle scale

A: 1/25000 scale is considered as  A) small scale  B) none of these  C) large scale  D) middle scale

Q: Define People ware, Software, and hardware and its relationship to CAD

A: Peopleware represents one of the 3 core component of computer technology other 2 are software and…

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.