Given the drawing below, answer questions 14, 15, and 16. 9992 9987 1,0008 T 1.0000 14. What is the tolerance on the shaft, 'S' ? 15. What is the tolerance on the hole, 'T' ? 16. What is the minimum clearance between parts 'S' and 'T' ?

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.

A: 13.A full section results when the cutting plane is completely passed through a part feature.Hence,…

Q: Hi is there any way the format can be changed a little bit so I can see the full explanation?

A: Given Data

Q: Thank you

A: given : t = 6.07mm = 0.00607 m F = 38.9 KN = 38900 N τ = 54.4 MPa = 54.4 x 106 N/m2

Q: Consider typical characterstics

A: The casting process is used for the various type of large and complex shapes as these shapes are…

Q: can I have FBD for this?

A:

Q: s Tafel p

A: introduction: here we have to explain tafel pot.

Q: If a sample of iron is cut in half, do the two pieces have the same density as the original sample?…

A: Here, density is defined as mass per unit Volume. and density is intensive property. Intensive…

Q: Introduction for shaper work process please elaborate in 200 words

A: Shaper is a material removal machine of reciprocating type motion, and used for producing flat…

Q: friction for both wedge surfaces is 0.30 and if the coefficient of static friction between the block…

A: Given data, Mass of the rectangular block, mb = 500 kg Angle of the wedge, α=5° Coefficient of…

Q: The designer should check on the standard shapes and sizes from the supplier of raw material and…

A: Given : Component shapes in which machining has to be done To find : Design rules for machining

Q: MANUFACTURING

A:

Q: Why should the thermal stresses be considered in design?

A: The stresses generated due to rapid heating or cooling of the structure are known as thermal…

Q: Figure A. Rectangular block of steel. Adapted from: https://media.wdscomponents.com/ri-…

A: Given: Workpiece is slimmed using slab milling To find: 4 items need to perform slab milling process

Q: The main part of the product consists of a polyurethane sponge

A: • Strength & Durability:When the upholstery is produced using high grade resins, only a thinPU…

Q: B- What are the differences bétween régular carbon steel and stainless steel and cast irons?

A:

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: 9. The top view shows a bend radius of the thin metal. Would a bend radius of 1/8" meet the…

A: If the bend radius lies with in the given range then it will meet the requirements. 18"=0.125" The…

Q: I need answers for problems 10, 11, and 12 pertaining to the print provided.

A: 10.In general, the reference dimension is used for information purpose only. It doesn’t have any…

Q: For casting processes in metals, which of the following are true? (This question has more than one…

A: Explaining casting processes in metal.

Q: What is the cutting speed of a material with a radius of 40 mm and a speed of 1000 rpm?

A:

Q: What are the types of irregular grids ? Support your answers with relevant diagrams

A: An unstructured or irregular grid consists of triangles and quadrilaterals (2D) or tetrahedral,…

Q: what effects does casting have on material properties

A: Casting is the process of preparation of mold which is poured into the hollow passage/ cavity of the…

Q: Consider the "roll lormed member shown in (Eszure.1) Suppose that a 50 mm, 6-200 mm Figure F-tyt.…

A: Given-Information: a=50mmb=200mm To-Determine: Location of  y¯ of the centroid C.

Q: Hello, sorry for not clarifying which parts to solve, could you please do part D?

A: Given data:- The speed of the impact is doubled To find:-the maximum compression of the spring

Q: Which of the following is a suitable process for creating a hollow 3D shaped component?

A: Option a is correct.

Q: Hardness is defined as:   a. The density of the materials surface layer   b. The density of the…

A: The hardness of a material is how strong or resistance to wear it is, measured by indenting the…

Q: Question 7 A precision metal part needs to be manufactured using a casting process. The part needs…

A: given; for high dimensional accuracy less than 2kg which manufacturing process should be used?

Q: How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is…

A: Given data as per question Object distance(u) =80 cm =800 mm Focal length(f) =32 mm  Here Location…

Q: What would be the result of the Yielding of the material?

A: In stress-strain curve of material the yield point is the point of elasticity. Yield points shows…

Q: 1. Wire drawing is cold working process use to decrease the dimeter of wire. A) Explain th process.…

A: 1. wire drawing

Q: Hello. Would it be possible to get a solution with detailed explanations? Thank you

A: Given: The mass of disc X, mx = 25 slugs The mass of disc, y = my = 12 slugs The speed of disc x, Vx…

Q: Processing of engineering materials. Discussion of various processing/techniques explain the…

A: Primary forming processes: It is a process under which the raw material convert into the industrial…

Q: As shown in fig.(2). Prove the main equation for the coefficient of frictional force between the…

A:

Q: How did you determine the 63.2%

A: Given Data:   To Find: Generate a mathematical model from the given data.

Q: have you figured out part b yet?

A: To determine the magnitude of the reaction force at each bearing, we'll relate the acceleration of…

Q: can please help me understand how someone could possibly do 75 windmills in a minute?? with madeup…

A: It is asked to perfrom basic analysis while performing 75 windmilles in a minute.

Q: should be the wall thickness am teel with a design factor of 3 the wall thickness and weight

A:

Q: What are the concentrated forces?

A: Concentrated forces are more a  mathematical idealizations than a realistic. Force applied at a…

Q: Using circles, draw regular two-dimensional arrangements that demonstrate low packing efficiency and…

A: Given question is related to material science.

Q: What is the working principle of balancing?

A: