Given the data of sieve analysis of the soil; 1. Determine the approximate effective size of the soil 2. Determine the approximate coefficient of curvature 3. Classify the soil using the AASHTO classification system

Given the data of sieve analysis of the soil; 1. Determine the approximate effective size of the soil 2. Determine the approximate coefficient of curvature 3. Classify the soil using the AASHTO classification system

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the following soil properties of a road grading works. Moist unit weight = 19000 N/m³ Moisture Content = 12% Specific Gravity of soil solids = 2.66 Void ratio at its densest state = 0.44 Void ratio at its loosest state = 0.62 Determine the dry unit weight of the soil. Determine the in-situ void ratio of the soil. Determine the relative density of the soil
U B. ( A Soil Specimen has the following characteristics: % passing No.4 sieve = 85 % passing No.200 sieve = 11 D60 = 2 mm D30 = 0.35 mm D₁0 = 70 μm L.L = 36% P.L = 31% D8 = 2 µm 1. Classify the specimen according to the Unified Soil Classification System (USCS). Assign the group name and the group symbol. 2. Determine the soil activity. 3. Determine the soil Liquidity index and consistency index if we = 26%.
2b. The following data was obtained from Sieve Analysis conducted at a Soil Lab. Using the data given in Table 02 determine: Table 02: Sieve analysis data of coarse-grained soil i. ii. iii. + Sieve Opening (mm) 20 10 4.75 2.36 1.18 0.6 0.3 0.15 0.075 Pan Mass of Soil Retaining on each Sieve (g) 5.21 20.21 180.21 360.21 280.11 70.11 50.21 17.21 10.11 8 Percentage of clay, silt, sand and Gravel in the soil sample Uniformity coefficient and coefficient of curvature Classify the soil according to BS soil classification system
2. The following data were recorded during particle size analysis tests in the laboratory. Plot the grading curve and determine the grading characteristics. Using the information, classify the soil according to BSCS. Soil 1 Fine-Mesh dry sieve analysis data: Sieve Size 425 (mm or um) Mass 1.18 600 300 212 150 63 retained 1.9 3.2 8.1 10.4 22.7 126.1 (g) Total sample = 212.0 g
Mechanical analysis on four different samples designated as A, B. Cand Dwere carried out in a soil laboratory. The results of tests are given below. Hydrometer analysis was carried out on sample D. The soil is non-plastic. Sample D D. liquid limit w 42, plastic limit = 24. plasticity index = 18 Classify the soils per the Unified Soil Classification System. Samples ASTM Sieve Percentage finer than Designation 63.0 mm 100 93 20.0 mm 64 76 6.3 39 100 65 20 mm 600 212 63 A 20 24 98 59 12 90 54 9. 47 100 34 95 23 69 7. 46 2 31 B and 100 60 20 Sand Course lo medium Cotles l>762 mm Clay Silt Gravel Fine 0.001 001 0.075 0.1 10 100 Particle size (mm) Figure Ex. 3.21 Percentage finer
A 59m3 soil sample having a degree of saturation of 96% at the liquid limit of 29%. At the plastic limit of the soil has a volume of 42m3. This soil sample was subjected to sieve analysis in the attached photo below. Find: a.Void ratio at Plastic limit b.Plastic limit c.Modified percentage of sand, silt and clay d.Classification of soil according to USDA
A sieve analysis is performed for a soil sample. The data are tabulated as shown. Solve Cu
A soil sample has the following size distribution; 4 to 2mm = 17%, 2 to 0.05 mm = 12%, 0.5 to 0.005 mm = 22% 0.005 to 0.002 mm = 10% <0.002 mm = 39% what is the percent clay silt and sand? What are the modifier and textural classification?
As a result of sieve analysis and hydrometer analysis on a soil sample, gravel 40% and sand 18%. Liquid limit value of the soil 58% and plasticity index was determined as 32%. D60, D30 and D10 values according to grain distribution curve 2.4mm, 0.9mm and 0.2mm respectively. According to the findings obtained, the soil sample Make USCS classification.
A soil sample retains 40% and 30% of total soil sample on 4.75 mm and 0.075 mm sieve respectively. It passes 10% when sieved through 0.002 mm sieve. Find the ratio of coefficient of curvature to coefficient of uniformity.
Mechanical analysis on four different samples designated as A, B. Cand Dwere carried out in a soil laboratory. The results of tests are given below. Hydrometer analysis was carried out on sample D. The soil is non-plastic. Sample D D. liquid limit w 42, plastic limit = 24. plasticity index = 18 Classify the soils per the Unified Soil Classification System. Samples ASTM Sieve Percentage finer than Designation 63.0 mm 100 93 20.0 mm 64 76 6.3 39 100 65 20 mm 600 212 63 A 20 24 98 59 12 90 54 9. 47 100 34 95 23 69 7. 46 2 31 100 60 20 Sand Coles >762 mm Clay Silt Gravel Fine Course lo medium 0.001 001 0.075 0.1 10 100 Particle size (mm) Samples A,BandC Figure Ex. 3.21 Percentage finer