Given the data below:   Mass of the Container                                             - 275 grams Mass of the Oven-dried Aggregate + Container  - 3145.2 grams Mass of the SSD Aggregate                                    - 3211.2 grams Apparent mass of the Aggregate                           - 1935.5 grams   Compute for the Bulk Specific Gravity of Aggregate in OD condition.

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: The concrete design needs to be like individual codes defining the terms of a complete building…

Q: civil engg material

A: Gradation of Aggregate- It is defined as a process that helps in particle size distribution which is…

Q: Test Procedure: 1. Fill the measure with aggregates (use compacted method). 2. Weigh the measure…

A:

Q: 3. For a particular aggregate, the bulk specific gravity (Dry) was 2.67,the porosity was 3%, and the…

A:

Q: Find the specific the surface in cm2/g of the fine aggregates knowing that its specific gravity is…

A: Given Data: The specific gravity of a fine aggregate is, G=2.65 g/cm3 The correction factor for all…

Q: The Flakiness Index test has been done on a 3500g of aggregate and it was found that 2780g failed to…

A: Using formula

Q: 1. Why do you think there is a need to agitate the aggregates inside the cylinder mold by rodding?

A: tests are done on aggregate so we can have information whether they are fit for use or not .  Note…

Q: The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in…

A:

Q: 1. Fineness modulus of the coarse aggregate Individual Cunulative Seive (nn) Weight Retained Percent…

A: Given data-

Q: The following information is available from a specific gravity test on fine a wt of SSD sand = 509 g…

A: A =weight of oven-dry sandB = weight of pycnometer filled with waterC = weight of pycnometer filled…

Q: What will be the mixing ratio of X aggregate when the following aggregates are mixed in such a way…

A: For the given data We have to find the mixing ratio of X aggregate such that 87% of mixed aggregate…

Q: Aggregates from three sources having the properties shown in the table below where blended at a…

A: To find -The properties of aggregate blend  Explanation :

Q: Based on the data shown in Table select the blend for a Superpave design aggregate structure. Assume…

A:

Q: is the grade size used to identified the practical grading of the aggregate O 4.75 mm O 600 micron O…

A:

Q: lease type your solutions in the box below. Answers without solutions will not have any marks.…

A: Note- Since we only answer up to 3 sub-parts, we’ll answer the first3. Please resubmit the question…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: According to ASTM C 33 Sieve analysis, the allowable aggregate sample should follow the below…

Q: 20. Calculate the solid volume and percent of voids of an aggregate that has a density of 1581 kg/m³…

A:

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 14 10 12…

A: Given Data: To Determine Fineness modulus of the Fine Aggregate Sample.

Q: Given the data in Table , select the blend and the design binder content for a Superpave design…

A:

Q: only as specified by the instruct 5.10 Samples of coarse aggregate from a stockpile are brought to…

A:

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: Sieve analysis: It is an analytical method that is used to determine the particle size distribution…

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

A:

Q: Review ASTM D75 and summarize the following:a. Sampling aggregates from conveyer belts.b. Sampling…

A: In a concrete about 60-80% of the volume and 70-85% of mass is aggregate.Aggregate act as a strength…

Q: Laboratory specific gravity and absorption tests are run on two coarse aggre- gate sizes, which have…

A: Solution Given Data The bulk specific gravity of aggregate A is G1=2.491 Bulk-specific gravity of…

Q: Aggregates from three sources having the properties shown in the table below where blended at a…

A: We have to determine the properties of aggregate blend for the data given in the problem. Below I…

Q: Three types of aggregate have sieve analysis as given below. Combine these types of aggregate to…

A: Sieve, inches3/41/23/8No.4No.8No.30No. 50No. 100No.…

Q: Based on the data shown in Table P9.31, select the blend for a Superpave design aggregate structure.…

A: Solution: The data of three kinds of blend is shown below: Data Blend       1 2 3 Gmb 2.451…

Q: A sieve analysis was conducted on a graded aggregate with a nominal maximum aggregate size of 20 m…

A: Soil boundaries give an idea of ​​its compatibility with soil and water or both compounds. When the…

Q: Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland…

A:

Q: Compute the compressive strength, in psi, for each size of aggregate on each no. of days of curing.…

A: Given, Compressive strength test data for 3/8" and 3/4" aggregates

Q: Given the bulk specific gravities of 2.65 for coarse aggregate, 2.69 for fine aggregate, and 2.73…

A:

Q: Please solve points 4 and 5 only

A: Detailed solution is provided belowPlease read carefullyAsk me if you have any doubtsThank…

Q: Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption…

A:

Q: Samples of coarse aggregate from a stockpileare brought to the laboratory for determination of…

A:

Q: Thoroughly mix the aggregate sample and reduce it to an amount suitable for testing, using a sample…

A: Sample Splitters: Sample splitters work by reducing the sample size by leading the flow of the…

Q: Sieve 1. A 500gram sample of fine aggregates was sieved. Determine FM 3/8" #4 #8 # 16 # 30 # 50 #…

A: Finness modulus is the sum of cumulative percentage of Weight retained on each seive and then…

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.