Given that w₁ = 4 kN/m, w₂ = 3.5 kN/m and a = 1.5 m, determine the the internal normal force (in kN), internal shear force (in kN), internal bending moment (in kN.m) at point D of the two-member frame. W1 A a ● D a a a E • B W2

Given that w₁ = 4 kN/m, w₂ = 3.5 kN/m and a = 1.5 m, determine the the internal normal force (in kN), internal shear force (in kN), internal bending moment (in kN.m) at point D of the two-member frame. W1 A a ● D a a a E • B W2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical. Positive values are to the right, up, and counterclockwise. y 39 4.3 kN 23 kN-m A B - - C 2.6 kN + 1.2 m 2.0 m 2.0 m Answers: Ox = i kN i kN Mo = i kN-m
P= 13 kN In the given figure, all the dimensions, loading condition and cross-section of the beam are given. If the allowable tension stress om= 120 MPa and the allowable compression stress oeme=100 MPa ; q=2 kN/m \B 4m 1m a) Construct the internal force diagrams (N, T, M). b) Calculate the moments of inertia (I, I, I„.). c) Check whether the beam can carry the given loading safely. К.С. 2cm 8cm 2cm 4 сm C. |G X+ 9 cm Note: The modulus of elasticity in the material is E=200 GPa, K.Ç. :Line of forces Kiriş enkesiti
Please answer properly.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
Determine the bending moment (M) in kNm at the point x = 4.5 m from point A for the beam as loaded in Figure 3.2b6. Given a = 2, b = 5 and w4 = 6. Wą kN/m C В a m b m
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
2. The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150×10° N/m?. The cross sectional area of each member is 0.01 m². Forces P1 and P2 are acting as shown, Wall (e= 40°, P;= 8 kN) 2 (a) (b) 40 (c) 309 P1 P= 2kN 4m FIGURE Q2 a. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by perfoming complete calculations to justify your recommendation. b. After the client approved your recommendation in (a), it was found that the displacements occurred at node 1 is still high. As a result, you are required to modify the truss design in order to reduce the displacement at node 1 by minimum 15% on a condition that modules of elasticity, and the force remain unchanged. Justify your recommendation.
How do i solve the attached trusses/civil engineering problem?
Please show the FREE BODY DIAGRAM and COMPLETE CLEAR solution
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa