Given that the transfer function H(S) s+ 10 then the step response will be +10 a+ 10 *+ 10

Q: Find the transfer function of the given circuit. RESISTANCE R INDUCTANCE CAPACITANCE i(t)

A:

Q: Sketch the root loci for the following open loop G(s)H(s). G(s)H(s): = s² +2s +1 s(s+3)²

A: Given:an open loop transfer function, To find:Root locus of the given transfer function.

Q: Determine K, a, and b so that the system with open loop transfer function has a closed loop pole at…

A:

Q: Q2. Reduce the boxes and then find the final transfer function: 4 1 X(s) Y(s) s+8 step unit 1

A:

Q: What are the zeros of the following transfer function: 2,000,000(s + 5) H(w) (s + 10) (s + 100)²…

A: Given, Transfer function: Hω=2,000,000s+5s+10s+1002

Q: Determine the step response of the following signal: 5[u(t) – u(t- 3)]

A: Determine the step response of the following signal.

Q: For the circuit shown below, R-10 KQ, L-20 mH, C-100 uF (assuming zero initial condition) Vo The…

A:

Q: X(s) ✓+ H₁ H₂ H₂ H₂ Y(s)

A:

Q: Reduce the block diagram shown in the figure below to a single transfer function T(s) = C(s)/R(s). J…

A: Given: Block diagram of a control system To find: Transfer function by reducing block diagram

Q: B) For the following block diagram, find the step R(s) 100 C(s) s(s+2) response: 0.1s+1

A:

Q: Q2 If the unit step response of a network is (1 – e-at), then Find its unit impulse

A: None

Q: s+1 The D.C. gain and steady state error for step input for G(s) = s²+8+1 are:

A: Given that, Transfer function, Gs=s+1s2+s+1

Q: Using masons rules, reduce the multiple subsytem then find the transfer function

A: The given block diagram should be converted into signal flow graph and ten we can apply masons rule…

Q: List down properties, find transfer function, frequency response, impulse response and output for…

A:

Q: -134

A:

Q: PROBLEM: Find the differential equation corresponding to the transfer function, 2s + 1 s² +6s+2…

A: We need to find out differential equation for given transfer function .

Q: 1. A block diagram is given as the following figure. R(s) + E(s) 5 Find the transfer function…

A: Given data, The block diagram is given as,

Q: need the transfer function

A: In this question,  We need to determine the transfer function .  We are solving this problem using…

Q: A second order system is described by the transfer function G(s) = 100/(s*s+ s+100). The percent…

A: Given second order system is described by transfer function G(s)=100s2+s+100

Q: Find the maximum overshoot in percentage for a unit step response for the closed-loop transfer…

A: Given: CsRs=10s+2s2+2s+2 Required: Maximum percentage overshoot.

Q: 3) Set VD(s) = 0 and find the transfer function V(s)/I*(s). This transfer function will give you the…

A: For MATLAB part, resubmit the question again. by using Masson gain formulaThe loops areLoop 1-…

Q: Find impulse and step output response

A: Brief description : Impulse response is defined for the input of impulse signal. Whenever input is…

Q: Find and plot the impulse response if possible: rt+2 y(t) = 3x(t).dt t-3

A:

Q: y(t) 2x(t). dt t-4 Find and plot the impulse response if poss

A:

Q: Determine whether the system defined by the following transfer functions are stable or not. Use…

A:

Q: A certain LTIC system has the following transfer function H(s). What is the impulse response h(t)?…

A:

Q: find the range of (y) and ( p , q, r) that locate the ploes of the following transfer functions in…

A: In the question,  Find the range of of all unknown parameter k, y, p, q we are solving this problem…

Q: Find the poles, zeros and the pole-zero representation of the system with the transfer function:

A:

Q: Compute the convolution of the signals x(t) =u(t)– u(t – 4) and h(1) = e"u(t

A: The system can be classified under various category: (i) Linear and Non-Linear systems, (ii) Time…

Q: H(s): 6s² + 18s +12 2s³ +10s² +16s+12

A:

Q: For the following control system, the transfer function C(s)/R(s) is R(s) C(s) 5 10 s(s+1) 3s Select…

A: In this question we need to find a transfer function of the given block diagram.

Q: Question 6 10 s(s+1) C(s) R(s)- Find the transfer function of the below diagram.

A: Diagram is given as,

Q: Model the following transfer function on Matlab and Simulink and find its response to a step input.

A:

Q: 6. What are thetime constantofthe following transfer function : 2 G, (s) G2(s) 0.5s+1 3s+2 a) 0.5 ,…

A: We need to find out transfer function for given system

Q: 1. Simplify the following block diagrams and find the transfer function C(s)/R(s) R(S) C(S) 12 S+8…

A:

Q: Find the poles, zeros and output time response for the following system. The input is a unit step…

A: We will try to find the poles , zeroes and the output response of the given transfer function using…

Q: Find the ramp response for a system whose transfer function is G(s) = (s+4)(s+8) Double check your…

A: G(s)=s(s+4)(s+8)G(s)=ss2+12s+32