A certain LTIC system has the following transfer function H(s). What is the impulse response h(t)? Make sure to do this by hand. You may check your answers using Matlab, of course, but you must show your steps as you would do it by hand 100 H(s) : = (2s + 10) (5s + 10)

Q: Find the transfer function of the given circuit. RESISTANCE R INDUCTANCE CAPACITANCE i(t)

A:

Q: Draw polar plot for the following open loop ?

A: The given open-loop transfer function is written below. Gs=20s2+s+0.5ss+1s+10. We need to draw the…

Q: The switch in figure below is in zero state when the step function input is applied. R=152k, L=0.5H,…

A: Ohm's law: This law states that the current is directly proportional to the voltage and inversely…

Q: Determine K, a, and b so that the system with open loop transfer function has a closed loop pole at…

A:

Q: Find the differential equation corresponding to the following transfer function C(s) 7s+1 R(s) 8s² +…

A:

Q: 6. What arethe time constantofthe following transfer function: G (s) G2(s) = 3s+2 %3D 0.5s+1 a) 0.5,…

A:

Q: What steps need to be taken to solve this type of question? Just solve one or two.

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Consider the RC circuit shown in figure. Find the following: (a) The governing differential equation…

A: Given data,

Q: Realize the following transfer function by cascading two first-order sections using inverting op-amp…

A:

Q: If an impulse is convoluted with a rectangular pulse, then the output will be: O an impulse a…

A: We need to select correct option for given statement.

Q: Q2 If the unit step response of a network is (1 – e-at), then Find its unit impulse

A: None

Q: A linear system is defined by the following block diagram and the impulse response, h(t), and an…

A: Given LTI systems

Q: s+1 The D.C. gain and steady state error for step input for G(s) = s²+8+1 are:

A: Given that, Transfer function, Gs=s+1s2+s+1

Q: Please don't use matlab please answer in typing format

A: Step 1: Given open loop transfer function…

Q: [Qs] Simplify the block diagram shown in the below figure and obtain the transfer function…

A:

Q: 2. Two systems are interconnected in parallel as shown in Figure 1a. The impulse response for each…

A:

Q: om 2) FC + Vi(t) R≤ Vo (t) Given the transfer function Vo(s). 10 Vi (s) S² + 3s +10 realize the…

A:

Q: 4ムッコー 5yLm-コ+yLa-2フ:タメCッ] The impulse response hin]is henコニ (A-B(4)")uca] Find the values of A and B

A:

Q: 2. For each of the following transfer functions, write the corresponding differential equation b.)…

A: 2. b Given Data: A transfer function(TF) of, Y(s)X(s)=s5+2s4+4s3+s2+4s6+7s5+3s4+2s3+s2+5 To Find:…

Q: R x(t) y(1) L= 0.75 H & R 20 Find and plot the gain and phase responses of the above circuit (show…

A:

Q: THE STEP RESPONSE (TO A UNIT STEP FUNCTION) OF A GIVEN SYSTEM IS SHOWN BELOW. THE SYSTEM IS: The…

A: In this question we need to determine the order of system.

Q: Consider the RC circuit shown in figure. Find the following: (a) The governing differential equation…

A: Given circuit,

Q: We have an input function x[n] and the impulse response h[n]. Make the graph of both in Matlab.…

A: The objective of the question is to plot the graphs of the given input function x[n] and the impulse…

Q: Convert this to the form convenient for constructing Bode plots. That is, place the denominator…

A:

Q: 3) Set VD(s) = 0 and find the transfer function V(s)/I*(s). This transfer function will give you the…

A: For MATLAB part, resubmit the question again. by using Masson gain formulaThe loops areLoop 1-…

Q: Simplify the following diagram to its final form and find its transfer function

A: Given: A block diagram of a control system as,  To do: Simplify the above diagram to its final form…

Q: The zeros of the transfer function s²+2s+2 s4+6s3 +4s²+7s+12 -1 and -2 -2-2j and -2 +2j O-1+jand-1-j…

A: We need to find out the zeros of transfer function .

Q: Th following figure shows the step response of an LTI system. What is the impulse response at n = 2.…

A: CONTINUOUS AND DISCRETE-TIME SIGNALS: Because a signal is a function, we truly mean continuous-time…

Q: Find and plot the impulse response if possible: rt+2 y(t) = 3x(t).dt t-3

A:

Q: The overall transfer function for the system below is

A:

Q: Find undamped natural frequency for the closed-loop system below such that the transient response to…

A:

Q: Find the closed-loop transfer function, T(s) = C(s)/R(s) for the system shown in figure below, using…

A: The given block diagram is, Determine,  T(s)=C(s)/R(s)

Q: Consider the RC circuit shown in figure. Find the following: (a) The governing differential equation…

A: Given circuit,

Q: Don't use matlab please answer in typing format

A: To sketch the root locus plot for the given open-loop transfer functions, we need to follow these…

Q: Unit Impulse Signal xample3: Solve the following. Example4: Solve the following. 4 | 8(t – 3)(t – 3)…

A: By the use of sampling property of integration of impulse function

Q: Vi (+) - LI elle L2 5 domain? - transfer function? R₂ R - Vo(+)

A:

Q: 23 Consider the transfer function: G(s) = 2s(4+2s) 4 H(s) = %3D 3s(3s – s²)+4 6+4s -S Using MATLAB…

A: The closed-loop transfer function can be calculated by using the open-loop transfer function and…

Q: 2. Apply a bilinear transformation to : 3 I(s) (s + A)(s+2) With T =0.1

A:

Q: : Comment on each step you need to obtain the second order transfer function which gives the…

A:

Q: > draw root locus for the following loop transfer function s2 + 2s + 4 s(s + 5)

A: