Given: Required diameter of hole = 20 num Thickness of plate = 25 mm Shear strength of plate - 350 MN/m Required: Force required to punch a 20-uum-diameter hole Puncher 20 mm e 25 mm thick h Punched out 25 mm 20 mm

Q: For the figure shown, if P = 50 kN and the vertical movement of end C is limited to 4 mm, then the…

A: Option -- 1250 mm2

Q: A full forming P= 50 kN axial force acts on the part shaped by the machining method made of xCy…

A:

Q: A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and…

A: The load is P=10 kN. The length is l=3 m. The cross-sectional area is A=1000 mm2. The modulus of…

Q: Q2: - A tape 100m long. it's cross sectional area in 0.0585 cm, the apparent length of which was…

A: Length L = 1500 m = 150000 cm Area A = 0.0585 cm2 Standardised pull Ps = 6.75 kg Actual Pull P =…

Q: (a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the…

A: Double D ring Below shows a Double D ring secured with a Nut and Bolt.

Q: A solid steel shaft is to be used to transmit 3,750 W from the motor to which it is attached. The…

A:

Q: D = 875 kN L = 1450 kN SECT. 2 SECT.1 Square Tubing Pipe Fy = 290 mPa Do 4.8m So S, = outide…

A: Question is not clear. Please upload the full question so that the understanding in problem may…

Q: A bar spring arrangement as shown in the figure is subjected to temperature rise given by Due to…

A: temperature rise given by

Q: Water flows through a 0.05 m diameter of cast iron as shown below. What percent of the total head…

A: Given Data: Diameter=0.05mk=0.9v=8m/sh=2m To determine:- percentage of total head loss caused by…

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the…

A:

Q: From the figure shown which of the following gives the best outside dimension of the square tubing…

A: Given: Length of the column, L = 4.8 m Support condition: One end is fixed and the other end  hinged…

Q: Rigib bar AB; attached to two vertical rods as shown, Is horizonta before the lead P is applied. If…

A:

Q: The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the…

A:

Q: The beam shown requires two plastic hinges for its collapse mechanism. y = 120 W₁ = Mp (40) The…

A: Answer  (1) We know that required number of plastic hinge in a structure for its collapse is given…

Q: A hydraulic punch press is used to punch a slot in a 0.40-in.-thick plate, as illustrated in the…

A:

Q: Two semi-spherical thin-walled vessels are joined together by attaching 40-mm bolts around the…

A:

Q: As shown in the figure below, determine the internal loadings at point C. B 0.1 m 0.5 m C A -0.75 m…

A:

Q: The drill is jammed in the wall and is subjected to the torque and force shown in 20 N-m 125 mm σA =…

A: A drill is subjected to torque, we need to find out the normal stress and transverse stress at point…

Q: Determine the proportional shear stress for a material that has a modulus of rigidity of 30 GPa and…

A: Given data : Shear  strain=0.0001Modulus of rigidity (G)=30 GPa

Q: Question 3 An 4.3 meter aluminum square wire is hanging vertically. A tensile load of 350 KN is…

A: As per bartleby policy i can do only one question at a time. Please upload again other questions.…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A:

Q: Fig shows a brass bar having cross-sectional area of 1000 mm subjected to axial force . Find the…

A:

Q: STATICS For the figure shown, if the resultant of the forces is acting at the slab center, O O 10…

A:

Q: Calculate the nominal flexural strength of the following section: 140(mm) A, =1000(mm²) 400(mm) As =…

A:

Q: need the answer quickly

A:

Q: Fig shows the bar subjected to a tensile load of 50 kN find: (i) the diameter of the middle portion…

A:

Q: 1. (a) A (110+X) mm long cylindrical rod is subjected to an axial tensile load of 110 kN, and a…

A: Determine, (i) shear stress, (ii) modulus of elasticity of the material(E).

Q: Calculate quantity of the Reinforcing for the beam shown in figure below. A 0.3 m 3.2 m 2016 08 @…

A:

Q: below, compute the magnitude of the force (F) required to break contact at point (c)?

A: From the given figure, the magnitude of F to break the contact point C has to be determined.

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt? D…

A:

Q: As shown in the figure, a hole is to be punched out of a plate having a shearing strength of s =…

A:

Q: A major collector has three 12 foot lanes including one shared-left turn lane and 1 thru lane in…

A: The banking of a road along a horizontal curve known as superelevation enables drivers to safely and…

Q: explanation and formula , Please do not copy paste the

A:

Q: nm. The bar is 1001 long. At the 26-ki 1oad, the str Determine a) the modulus of elasticity. b)…

A:

Q: 3 m 2 m P = 50 kN Area (mm2) length E 70 Gpa 200 Gpa Aluminum 500 4 m Steel 300 3 m Aluminum Steel

A:

Q: An axial load P is supported by a short steel column, which has a cross-sectional area of 11200 mm².…

A: First calculate the maximum load that can be sustained by the column. Then using that value the…

Q: FA-8 kN and Fa-3 kN, represent the force system by a estant force, and specity its location on the…

A:

Q: Activity 1: Read with understanding and solve the following problem carefully and honestly: Write…

A: The given figures are shown below:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.