given: Q2A=12 INCHES AB= 2FT 4 INCHES BC= 8 INCHES DE = 1 FT 3 INCHES Q7E= 12 INCHES Q5C= 2 FT DF= 2 FT CE = 3FT Ks -> use appropriate scale Kv -> 400ft/min= 1 inch Va= 472 ft/ min ☆ Solve the velocities of F and E by Resolution and Composition ☆ pls show the output

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution

A: Step 1: Step 2: Step 3: Step 4:

Q: given below, in the arm slide mechanism, the actuating limb angular position is (theta)θ12 = 600 and…

A:

Q: Analyze and sketch a graph of the function. Find any intercepts, relative extrema, points of…

A:

Q: Problems: -1 For the figure shown, below, VA = 2.5 1/s in the direction shown ) Make scaled drawing…

A:

Q: Design a four bar linkage to generate the function y=x²-1 for values of x between 1 and 5. Use…

A: To solve this problem, we need to design a four-bar linkage that generates the function  the for…

Q: Find the parametric equation of the two lines fu) and gfv) from the figure below, then detect the…

A: The points (0, 0, 0) and (3, 3, 0) represent the line f(u) as given in the figure. The general form…

Q: speed of the cart

A:

Q: The figure deg/sec. In this case, the times are given as t = 5 sec and t-30 sec. In addition, the…

A:

Q: 3. Find Vg and Vc AO2=30mm B AB=60mm AC=80mm BC=45mm

A:

Q: Example - Single cylinder 4-stroke engine The torque diagram for a single cylinder engine is shown…

A: Given1cm=100 Nm1cm=90degN=1500 rpmn=±2%σh=5 MN/m2ρ=7200 kg/m3

Q: The acceleration of A is 3.5 m/s dovwnward and the acceleration of Cis 2.3 m/s upward. Find the…

A:

Q: Don't Use Chat GPT Will Upvote

A: Step 1:Step 2:Step 3: Step 4:

Q: . A force F=10Sint Newton acts on a displacement of x=2Sin(xt-r/6) meters. Determine (a) the work…

A:

Q: Draw and discuss the FBD for the following system. • Label all forces and directions. • How many…

A: K

Q: Please help with this question    write out the equation of conservation of momentum below.

A: mass of ball m1=1.5 kg mass of ball m2=1.5 kg

Q: The :Q4 = 26 in.; CBE = 27 in. represents a crank and rocker m used in a certain type of wool-…

A: To given thatQ2B=5in                  Q2Q4=26inBC=15in                   CBE=27inQ4C=21in…

Q: Given data: U=2 m/s V=2.8 m/s t=0.3 s Find acceleration

A: Given data : Initial velocity=U Final velocity=V Time=t   Required : Acceleration

Q: The velocity of pin C relative to the slot is 26 in/s upward and is decreasing at 50in/s². Part A…

A: The objective of the question:(a) What is the angular velocity of the bar AC?(b) What is the angular…

Q: A particle moves along the x-axis with the velocity history shown. If the particle is at the…

A:

Q: 1. A force F=10Sint Newton acts on a displacement ofx=2Sin(t-t/6) meters. Determine (a) the work…

A:

Q: A ball (2 kg) moves with a speed 6 m/sec, the required force to stop the ball in 7*10-4 sec equals…

A:

Q: The device shown below uses a hydraulic piston to hoist cars over the range 20 ≤0 ≤90. The piston…

A: Solution: Given Data: s.=0.1 ft/s20o≤θ≤90o   To Find: (a) The expression for the velocity. (b) The…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: To solve the problem, we need to find the velocity-displacement equation, the period, and the…

Q: Given: The plane accelerates in its current trajectory with a= 100 m/s^2 Angle theta= 5° W=105 kips…

A:

Q: In the figure shown, if wa=300rpm , solve for (a) the angular velocity of disk C (in rad/s) (b) the…

A: Given data ωA = 300 rpmrA = 2 inchrB1 = 4 inchrB2 = 2 inchrC = 6 inch

Q: * quiny 500 M T₁. T.₁. Fig.2

A: Given system is  Newton’s second law,  Inertia force = net restoring force

Q: Two cables AB and AC are acting on the pole with forces FAB 540N and FAC=560N with parameters…

A: Given: AB = 540 N coordinates are written in vector form and unit vector is found.

Q: n flow measurement’s industrial application there is checking the force exerted by steam inside a…

A: Given Data⇒ Flow measurement’s industrial application force exerted by steam inside a vessel

Q: None

A: Q.3) True Q.4) False Q.5) False

Q: The image below depicts one section of a cam shaft which opens a valve to release the pressure in…

A:

Q: Given data: Initial velocity=8 m/s Final velocity=17 m/s Time=2 s Find acceleration

A: Given data : Initial velocity=U Final velocity=V Time=t To find : Acceleration

Q: TRANSCRIBE THE FOLLOWING SOLUTION IN DIGITAL FORMAT PLEASE

A:

Q: 8 From the image below, identify the values of the position coordinates A and Buss ging the given…

A: To determine:sAsB

Q: A centrifuge in a medical research laboratory rotates at an angular speed of 3,750 rev/min. When…

A: