Given: In the series R-L-C circuit; R1 = 150-Q, R2 = 750-N, XL1 = j 1250-Q, XL2 = j 300-0, Xc1 = -j 900-0, Xc2 = - j 250-0 and e(t) = 40 sin(200t) v. Find: a) total impedance b) total current in the ckt. c) voltage drop VR; Vc and V. d) total power and power factor j1250ehms 150ohms -1900ohms 750ohms ll 1300ohms -1250ohms

Given: In the series R-L-C circuit; R1 = 150-Q, R2 = 750-N, XL1 = j 1250-Q, XL2 = j 300-0, Xc1 = -j 900-0, Xc2 = - j 250-0 and e(t) = 40 sin(200t) v. Find: a) total impedance b) total current in the ckt. c) voltage drop VR; Vc and V. d) total power and power factor j1250ehms 150ohms -1900ohms 750ohms ll 1300ohms -1250ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6-10) Using what you have learned constructing the phasor diagram for the LRC series circuit, construct a diagram for the LRC parallel circuit. Derive an expression for the circuit impedance Z and the phase angle φ between the applied emf and the current supplied by the emf. HINT: in the series circuit, the current through all four components was the same. Ask yourself what the components in this arrangement have in common.
With due respect, Sir can you Give full explanation how to solve this math and Assignment question topic .It would be very helpful for me if you give it with clear definition.
from the equation below, where did the -0.5 and j0.1768 came from? can you show the computation? Thank you!
Dc circuit analysis : nodal, loop, and superfositiron a) In the Circuit given, deactivate the GV Source byusing Cny DC analysis calculate lo Cnd Vo due to the technique, 12V Sourd. b) Deactivale the DC Circuit analysis Vo 12V source and use any tech niquet calculate the to and due to the lev source. ) Calcu la le the nit lo and Vo due to both Sources.
Q: For the following SLD, take Sg = 100 MVA and VB = 22 kV at Bus 1to:1. Draw the impedance diagram with all impedances in pu2. Find Em- 30 MVA40 MVA30 MVAX= j0.6 puX= j0.3 pu(40:15) kV18 kV(15:35) kVEgEmX= j0.3 pu(3+j4) QT.L50 MVA Ti Bus 1Bus 2 T2Load40 MVA23 kVBus 318 kVX = j0.5 pupf = 0.65 lead
852 J452 Tz Q.7: For the circuit shown: 1. Write the voltages w.r.t currents equations (Z- + Parameters). 2. Find the voltage gain if (Z=4Q). (Ans.: Z11= Z22=3.25+j2, Z12= Z21=0.75+jQ & 452 452 VI V2 12n J20
Reply as soon as possible and clearly, do not use italics 1) For the circuit in Figure, what is the value of S1, S2, S3, S4 and ST? Response format: a complex number in rectangular format. 2) What is the power factor of the circuit? (Response format for power factor: a number real rounded to two decimal places) and What is the value of the impedance seen by the source? ( Response format for impedance: a Complex number in rectangular format.)
moduleMSX-83fromBPsolarisusedinthefollowingconfigurationtomakeaPVarray: •4modulesinseries •2strings(of4modulesinseries)inparallel TheelectriccharacteristicsatSTCaregivenbelow: Maximumpower(Pmax)=83W Short-circuitcurrent(Isc)=5.27A VoltageatPmax(Vmp)=17.1V Open-circuitvoltage(Voc)=21.2V CurrentatPmax(Imp)=4.85A WhatwillbetheelectriccharacteristicsofthePVarray?
NOTE: Polar form for Voltage & Current. Rectangular form for Impedance Find the total impedance of the circuit, total power (apparent) delivered by the current source, Draw the phasor diagram of the voltage and current at the source, the current passing through the R2 and L1 branch, Draw the phasor diagram of the voltage and current at the R2 and L1 branch. Also, is the circuit inductive, capacitive, or neither (resistive)?