Given four resistors R1 = 100 ohms, R2=250 ohms, R3 = 350 ohms, and R4 = 200 ohms such that R1 and R2 in parallel will be connected in series with R3 and R4 in parallel. The series-parallel combination is connected across a 24-volt DC power supply. Find the voltage across R2 and voltage across R4 voltage drops across R2 and R4 are both 12 V voltage drop across R2 is 8.63 V and voltage across R4 is 15.37 V voltage drop across R2 is 8.63 V and voltage across R4 is 15.37 V voltage drop across R2 is 18.63 V and voltage across R4 is 5.37 V

Given four resistors R1 = 100 ohms, R2=250 ohms, R3 = 350 ohms, and R4 = 200 ohms such that R1 and R2 in parallel will be connected in series with R3 and R4 in parallel. The series-parallel combination is connected across a 24-volt DC power supply. Find the voltage across R2 and voltage across R4 voltage drops across R2 and R4 are both 12 V voltage drop across R2 is 8.63 V and voltage across R4 is 15.37 V voltage drop across R2 is 8.63 V and voltage across R4 is 15.37 V voltage drop across R2 is 18.63 V and voltage across R4 is 5.37 V

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 71PE: Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic...

See similar textbooks

Similar questions

Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off allowing a person to work on the electronics with less risk of shock, (a) What is the time constant? (b) How long will it take to reduce the voltage on the capacitor to 0.250% (5% of 5%) of its full value once discharge begins? (c) If the capacitor is charged to a voltage V0through a 100-O resistance, calculate the time it takes to rise to 0.865V0(This is about two time constants.)
1///
The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 8.5V what is V3? C R L V2 V3 21.5 V 8.5 V 15.53 V 4.5 V 13 V
Asap plzzzz
Three resistors with resistances R1 = 11.5 ohm, R2 13.5 ohm, and R3 = 17.1 ohm are is series circuit with a 25 volt battery. How much current (Ampere) can %3D move through the circuit?
PS 2: A 12-volt battery of internal resistance r of 0.05 ohm is to be recharged u, source at the rate of 8 amperes. 30-volt dc a. What resistance R is to be connected in series with the circuit? ANSWER: b. What is the terminal voltage of the battery? c. How much energy in joules is dissipated in the resistor in one hour ? ANSWER: ANSWER:
In the circuit below R1 = 33 Ω, R2 = 64 Ω, R3 = 118 Ω, and V = 95 V. What is the magnitude of the voltage drop across the R2 resistor?
explain why all measured voltage is not same with estimated voltage in using multimeter as a voltmeter to measure voltage.
What is the output voltage in the circuit below if Vin =2.5 V (DC)? Your answer should be in Volts and be an exact number.
What is the output voltage in the circuit below if Vin =2.0 V (DC)? Your answer should be in Volts and be an exact number. 7V Vin Vout R1 5 kN -7V R2 1 kN
Circuit Problem: Express each labelled voltage and current (e.g., vx, ix) in terms of the resistances and source currents and voltages (e.g., R0).
Shown in the figure below is an RC circuit. At t=0, the capacitor already contains a charge and as a result has a voltage of 7.30 Volts. The resistor has R = 5725 N, and the capacitor has C = 3.81e-06 Farads. At t=0, the switch is closed. ww switch Enter a number. Determine the time constant of the circuit, T= x seconds Fill in the table of formulas below. Use numerical values for the "max" column and a formula for the "form" column: max form Qcap(t) |× c -() e X V e ()- Vcap(t) Vres(t) e X A е -() Ires(t) • Determine the current at t=3.23e-02 seconds. X Amps NOTE: The entries for "max" are numerical. The entries for "form" leave out the leading coefficient. Here are examples: If the answer was: max: form: Q(t) = 12 sin(@ot) 12 sin(@t) V(t) 45 log(t/t) 45 log(t/t)