GIVEN: FOR A SHORT PERIOD OF TIME, THE MOTOR TURNS GEAR A WITH A CONSTANT ANGULAR VELOCITY OF 4.5 rad/s. DETERMINE THE VELOCITY OF CYLINDER C AND THE DISTANCE IT TRAVELS IN 5S. THE CORD IS WRAPPED AROUND PULLEY D WHICH IS RIGIDLY ATTACHED TO GEAR B. REQUIRED: SOLUTION: v=w.r WA-415 rad/s 75 mm AG P B 225 mm D C 125 mm virrin

Q: From the given beam loaded has shown; Ely = ¹/R₁x² – M₁ (x − 2) + C₁, Ely = R₁x³ - ²/M₂(x - 2)² +…

A: Given data: EI(y')=12RAx2-M0(x-L2)+C1EI(Y)=16RAx3-12M0(x-L2)2+C1x+C2M0=47 kNmL=8mIt is asked to…

Q: The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown.compute the vertical reaction…

A: Diameter of cylinder (d) = 5 ft  Length of cylinder (L) = 5 ft Weight of cylinder (W) = 5000 lb…

Q: The triangular distributed load acting on the beam can be replaced by a concentrated load of ...…

A:

Q: Neglecting any viscous resistance from the bottom of the cylinders, develop an algebraic expression…

A: Following is the given information: Ri is the inner radius of the viscometer.Ro is the outer radius…

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A:

Q: Ex Determine the required lengthef cord(AC) in figure, so that the (8 ka) lamp can be suspended in…

A:

Q: Oil (0.80)

A:

Q: The hoist supports the 200-ka engine shown, Answer the following questions

A:

Q: The tractor mounted bucket is controlled by an identical and parallel double mechanism, one of which…

A: To find the forces in the members BC and DE of the system.

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A:

Q: CALCLULATE THE FEM OF THE FOLLOWING USING THREE MOMENT EQUATION.

A: Calculation of FEM using three moment  equation

Q: 700 N.m D 0.6 m 1.2m

A:

Q: The flywheel A rotates clockwise under the action of a 700 N-m couple. A band break is to be used to…

A:

Q: a0 EN I00 KN WHEEL LOADS 4M âm la m 23V OOR4TAAXINVM BENDING MOMENT AVIEBUOOLIMC 2EBAICE2 MAX IMUM…

A:

Q: Q2:- A steel cylinder of (s.g = 0.64) floats on water, submergence, h? find the depth of 4cm Water…

A:

Q: (b) Neglecting any viscous resistance from the bottom of the cylinders, what is the value of 4, when…

A: Considering the given data a=0.2 mmR1=50 mmh=80 mmM=0.0245 N.mmΩ=1.2

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A:

Q: Example 123. The compound beam is fixed at A, pin connected at B, and supported by a roller at C.…

A:

Q: Determine the resultant force Por the Rorca system shown below. 201bA 10016 80 1b in

A:

Q: Two circular shafts are joined together between fixed supports to resist a orsional moment of 80…

A:

Q: When the inner cylinder is rotating and the outer cylinder is stationery, in reality, viscous torque…

A:

Q: The 480-lb V-8 engine is supported on an engine stand and rotated 90 degrees from its upright…

A: It is Given that :

Q: 300 mm B 600 mm 400 N·m 600 mm 200 N·m 800 N·m The 50-mm-diameter A992 steel shaft is subjected to…

A: given data,change solid steel shaft into the tabular cross sectionFindAngle of twist at AMaximum…

Q: 4 KN 3kN Sm C 5m Ē Sm Ġ 5m The reaction at Ay is || KN (two decimal places) The reaction at Hx is KN…

A:

Q: Fluid enters through the eye of the impeller and then travels outward between the vanes of the…

A: Given - Fluid enters through the eye of the impeller and then travels outward between the vanes of…

Q: In a workshop, drilling operation is performed using a hydraulic system. Cylinder B is used for…

A: In a workshop, drilling operation is performed using a hydraulic system. Cylinder B is used for…

Q: The distributed load acting on the beam can be replaced by a concentrated load of A acting at A from…

A:

Q: Determine the magnitude of the reaction Ay and Dy of the figure shown.

A: The given figure is shown below:

Q: water 3cm D=5 cm Mercury The tank in the has a plug at the 5cm diameter bottom. on the rrght. All…

A:

Q: Q/ Find the reaction forces at point (B)

A: Given Data:W=300kg= 300×9.81=2943NL=3.6m

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A:

Q: (a) For the input force, P, determine the force exerted on the bolt. (b) What is the mechanical…

A: It is given that :

Q: A compressor reed valve is made from a flat piece of metal. The reed is 0.8centimeter long. When gas…

A: Given:- angle=25 degree reed=0.8cm long To find:- height

Q: 35L 口 101 -10 n- El- constant MEMBER AB BA BD DB DE ED DF FEM BAL COM BAL COM BAL COM BAL COM BAL…

A:

Q: (12) 2 A cylindrical srod which is fixed from both the ends as shown in fig., calculate the reaction…

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.