Answered: Given fc' = 35 MPa, solve for the…

Given fc' = 35 MPa, solve for the modulus of elasticity of concrete a. 27,800.00 MPa b. 27,805.57 MPa c. 200,000.00 MPa d. None of the above If fc'= 42 MPa, solve for B. a. 0.65 b. 0.75 C. 0.85

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A vinyl [E = 2.80 GPa; v = 0.41] block with width b = 50 mm, depth d = 100 mm, and height h = 270 mm…

A: E = 2.8 GPa = 2.8 × 103 N/mm2Poisson's ratio (μ) = 0.41Determine the change in the depth dimension…

Q: 3 Given a concrete beam (width b= 10 in., depth h=25 in.) with flexural reinforcement at the bottom,…

A: Cracking: When the stresses or the forces which are imposed on the structure cannot be resisted by…

Q: 1. Given concrete has density (Pcom.= 2000 kg/m²) and coefficient of friction (cf = 0.45), determine…

A: Given concrete density ρ=2000 kg/m3 And coefficient of friction μ=0.45hieght of concrete levee H=6 m…

Q: Problem 2: Design the following beam o, = 2 kip/ft (Not including beam weight) ®, = 4 kip/ft 12 in.…

A: Step 1

Q: The column shown is made by filling a steel pipe with concrete. The concrete has an Elastic Modulus…

A: Given Data: The Elastic Modulus of concrete is Ec=3800 ksi. The cross-sectional area of the concrete…

Q: Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in.…

A: Given Load 60,000 lbDiameter 3/4 inThickness 1/2 inTo find out Shear stress

Q: 5.9 A concrete test cylinder eight 8" tall and 4" in diame- ter is subjected to a compressive load…

A: Length of the cylinder (L) = 8 in. Diameter of cylinder (D) = 4 in.Linear strain (ε) = 0.003…

Q: A concrete is composed of a mixture 286 lbm of cement (SG = 3.11), 520 kgm gravel (SG 2.71), 260 kgm…

Q: 6. A 600 mm diameter column contains 20 - 28mmø bars arranged in a circle. It has a spiral bar…

A: The given data is: D=600 mm clear cover=40 mm Least lateral diameter of column, Dc=D-2(Clear cover)…

Concept explainers

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.

Question

Given fc' = 35 MPa, solve for the modulus of elasticity of concrete
a. 27,800.00 MPa
b. 27,805.57 MPa
c. 200,000.00 MPa
d. None of the above
If fc'= 42 MPa, solve for B.
a. 0.65
b. 0.75
C. 0.85

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A concrete masonry unit has actual gross dimensions of 7@5/8′′ * 7@5/8′′ *7@5/8′′. The unit is tested in a compression machine with the following results:Maximum failure load = 83 kipsNet volume = 312.7 in.3a. Is the unit categorized as solid or hollow? Why?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength.
2- A steel food is stretches between two rigid walls and carries a tensile load f 6000 N at doc. If the allowable stress is not to exceed 130 MPa at -24°C, what is the minimum diameter of the rod ? Assume + = 11.7 (106) M/C and E= 200 GPa. ST + 7 P=6000 8 Figure: P&CON L
0 ww C. 6.31 A concrete mix includes the following ingredients per cubic foot: a. Cement = 25 lb b. Water = 11 lb c. No admixture Table P6.31 shows possible changes that can be made to the mix ingredi- ents. Indicate in the appropriate boxes in the table what will happen in each case for the workability and the ultimate compressive strength as increase, decrease, or approximately the same. TABLE P6.31 to dignope Cement (lb) 25 28 25 25 25 25 25 amigur Water (lb) 15 11 11 8 11 11 11 Admixture None None Water reducer Water reducer Superplasticizer Air entrainer Accelerator What Will Happen? www.10345 Ultimate Compressive we Strength Workability
A concrete cylinder sample has a diameter of 6 inches and a height of 12 inches. The maximum load carried by the sample after its failure is 500 KN. Determine the compressive strength of the sample in psi. (use 1lbf = 4.45 N, round-up your answer to the nearest whole number that is divisible by 5, no need for unit)
2. According to Section 10.2.3 of AC, the maximum usable strain at extreme concrete compression fiber shall be assumed equal to a. 0.004 b. 0.005 c. 0.003 d. 0.002 e. 0.001 f. 0.008
solve the following problems 1. A concrete has a height of 5 meters and has unit area of 3 m². It supports a mass of 30,000 kg. Acceleration due to gravity (g) = 9.81 m/s². Young's modulus of concrete = 20x 10¹ N/m² Determine (a) the stress (b) the strain (c) the change in height.
Please help by showing ALL steps I am trying to see what I am doing incorrect on don't just want the answer
A concrete test cylinder is 150mm in diameter and 300mm in length. During an axial compression test the diameter increased by 0.1399 mm and the length decreased by 0.397 mm. The concrete has an ultimate compressive strength of 21Mpa, Ec=20,000Mpa. Compute the compressive load that caused the above deformations
The concrete post in the figure is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm?. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Bearing | 1000 kN plate Steel Concrete 300 mm 300 mm Section a-a The stress in concrete = MPa (use up to 4 significant figures). The stress in steel = MPa (use up to 4 significant figures).
PROBLEM TO SOLVE: 600 mm 400 mm 6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa) d. Moment of Inertia under critical condition e. Demand Capacity Ratio of Concrete under Compression Stress f. Compression force on concrete (kN) g. Distance of the compression concrete force from the neutral axis (mm)