Given: BEW-5,600 lbs BEW C.G.-15.5 feet Pilot - 180lbs Tank 1 Fuel - 400 lbs Tank 2 Fuel 1,800 lbs Arm to pilot-8 feet Arm to tank 1-14 feet Arm to tail-32.5 feet Arm to tank 2-19 feet What is the loaded C.G? (Give to two decimal places)

Q: Which of the following is not the unit of pressure ? A.Kg/cm2 B.Newton C.Atmosphere D.Mm of wcl

A: Given Data⇒ Pressure

Q: For the following figure, draw a kinematic diagram for each identifying the point of interest. From…

A: For the Given mechanism shown below  To determine  Draw kinematic diagram and calculate its…

Q: For a pump designation 1-x3-10 provided by the manufacture, find out the appropriate options for…

A:

Q: What is the V and M diagram? Thank you!

A:

Q: Figure 2 shows a beam subjected to distibuted loading. Knowing the beam is fixed supported at one…

A:

Q: Find reaction at A.

A:

Q: If a heavy cargo is lifted using a ship's crane and the load remains suspended within the ship, what…

A: When the heavy cargo is lifted using a ship's crane and the load is still suspended within the ship,…

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: Q) Write introduction and conclusion for Lift Mechanism Bucket Boom Shoulder Mount Base

A: Write the introduction and conclusion for lift mechanism.

Q: Find to the nearer thousandth inch the circumference of the ring that fitsaround this piston for a…

A: Given    Diameter, d = 0.8 in

Q: What would be the resultant force F of the triangular distributed load and its location 'd measured…

A:

Q: 2) Write introduction and conclusion for Lift Mechanism Bucket Boom Shou Mou Base

A: Parts of lift mechanism is- Base Mount Boom Shoulder Bucket

Q: How many hp of engine needed for a 3 Gross tonnage double Outrigger Boat?

A:

Q: If a cylinder rod exerts 5,000 lb of force extending, how much force would a single lever toggle…

A:

Q: Vertical axis wind turbine is one which has blades rotating on an axis parallel to the ground…

A: The blades of a horizontal axis machine rotate on an axis parallel to the ground. The blades of a…

Q: This is called the... baggage hold propeller cabin cockpit

A: Baggage hold is the system of aircraft which is used to hold baggage or to store the baggage during…

Q: shown in Fig. 2-13.2a. The inscribed grid with each square having a length of 1 ft locates each…

A:

Q: Finding support reactions

A: A loading forces are given. To determine, the reaction forces in both the supports.

Q: a,b,c please and thank you!

A: The objective of the question is to determine the maximum and minimum principal stresses and the…

Q: Q) Write introduction and conclusion for Lift Mechanism

A: Given:

Q: 100 lb 800 lb · ft A |C B 5 ft 5 ft

A:

Q: Explain by drawing a figure the recovery or capsizing (overturning) situation of a boat in the water…

A: Capsizing when a boat or ship is turned on its side or it is upside down in the water then…

Q: Estimate the heat loss from human body of 36 C temperature by convection and radiation. Consider the…

A: The heat loss from human body of 36oC temperature by convection and radiation is 304.875 W.

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: What is the magnitude of the Right Reaction force in pounds?

A: GIVEN: F=1.5 kpis =1500 lbf TO FIND: The reaction on the right side. Rb

Q: 1 kN/m 1m

A: Shear force is an internal force in any material which is usually caused by any external force…

Q: U-CHANNEL IRON BASE motor 0 MOTOR 3.7 kW 3600 RPM +1.78 +1.32 +2.92 140 pump 0 89 +0.13 +0.97) +1.22…

A:

Q: Does not change when fluid cannot be compressed. density mass flow

A: Since the volume of incompressible fluid does not change, therefore density of fluid remains…

Q: To decrease the amount of force needed increase the of the inclined plane. distance or length O…

A: Given Data⇒ Inclined plane

Q: Total number of zero force members

A:

Q: What is the mechanical advantage of this system?

A: We have to first draw free body diagram of the block and the pulleys and then derive a relationship…

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: A motor car tyre contained a fixed mass

A: Given Tyre To find Importance of mass in motor car tyre   Moto car tyre is to maintain the road…

Q: A cooling fan is connected to the driving motor by a V-belt. How many incheslong is the V-belt?

A: given:

Q: What is the area of a rectangular air supply opening measuring 12x10?

A: Given data  Side of a rectangular = 12 × 10 Find the area of rectangular Use  Area = length × width…

Q: Does this machine maximize or minimize the force (100 Ib) *

A: Reaction force acting on the point B is RB×1.5=100×20RB=1333.33 lb As the reaction force acting at…

Q: A mechanic is supporting a car with a hydraulic lift. The smaller piston has radius of 3 inches and…

A: Given data:- The smaller piston has radius =3 inches the larger piston has a radius = 8 inches.…

Q: 5. How many stable structure(s) are shown below? A. 0 B. 1 C. 2 D. 3 E. 4

A: The objective of the question:Determine the number of stable structures.  Given structure:

Q: 00 Ib, 120° 60°

A:

Q: The shaft is supported by a journal bearing at A and a thrust bearing at B. Determine the normal…

A: Given data  F1 = 2.5 kip  F2 = 3 kip W = 75 lb/ft b = 12 ft a = 6 ft c = 2 ft To determine…

Q: Q) Write introduction and conclusion for Lift Mechanism Bucket Boom Shoulder Mount Base

A: Write Introduction and conclusion for lift mechanism.

Q: The property of changing the volume of fluids by applying  external pressure are known as specific…

A: Compressibility: The property of changing the volume of fluids by applying  external pressure is…

Q: Consider the bar/roller assembly shown in the figure below. The roller and surface at point A are…

A: A free body diagram is defined as a diagrammatic representation of all the forces acting in a…

Forms of Energy

Energy is described as the capability to accomplish a task, like the ability to push a block by applying force on it. It is a quantitative property that is used to accomplish work on an object.