Given a manometer with tube diameter 0.6 cm and mercury length of 122 cm, theapplied pressure is suddenly increased from 15 cm to 20 cm (step change). If p =13.5 g/cm3 , µ = 0.016 g/cm. s, and g = 980 cm/s2 , Find:1. Period of oscillation.2. Overshoot.3. Decay ratio.4. Maximum peak.5. Natural period of oscillation.6. Rise time.7. Plot roughly the manometer reading

Answered: Image /qna-images/answer/e9588854-771e-47a0-aaf5-c8a761928a8c.jpg

Given a manometer with tube diameter 0.6 cm and mercury length of 122 cm, the applied pressure is suddenly increased from 15 cm to 20 cm (step change). If p = %3D 13.5 g/cm3 , µ = 0.016 g/cm. s, and g = 980 cm/s2 , Find: %3D 1. Period of oscillation. 2. Overshoot. 3. Decay ratio. 4. Maximum peak. 5. Natural period of oscillation. 6. Rise time. 7. Plot roughly the manometer reading

Given a manometer with tube diameter 0.6 cm and mercury length of 122 cm, the applied pressure is suddenly increased from 15 cm to 20 cm (step change). If p = %3D 13.5 g/cm3 , µ = 0.016 g/cm. s, and g = 980 cm/s2 , Find: %3D 1. Period of oscillation. 2. Overshoot. 3. Decay ratio. 4. Maximum peak. 5. Natural period of oscillation. 6. Rise time. 7. Plot roughly the manometer reading

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The life of an automotive component can be modelled by a Weibull distribution.∝ = 6.3 ? 105, ? = 1.3 i. Calculate F(t)ii. R(t)iii. h(t) at the end of the rotating period of 36,000 miles
Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW and the brake specific fuel consumption (bsfc) is 290 g/kW.hr. Air consumption is measured by means of air-box method with orifice diameter 3.2-cm and discharge coefficient 0.62 and the pressure difference across the orifice is 150-mm-water. The ambient pressure and the temperature in the test room is 101 kPa and 20 °C. Assume: CV = 43.9 MJ/kg, PH20 =10³ kg/m³, comb = 98%, mech = 87%. (i) Determine the bmep, AFR, №v, power loss as friction, th,b. (ii) draw up the heat balance sheet on percentage basis, if the cooling water flow is 15 kg/min; rise in temperature of cooling water is 33 °C; exhaust gas temperature is 485 °C; Cpw is 4.2 kJ/kg.K and Cpexh is 1.25 kJ/kg.K.
Consider the loaded shaft illustrated in Figure Q4 (i). The shaft is simply supported at A and D. The shoulder fillet radius is 0.3 cm at B and C. If the shaft is subjected to a force of F=800 N, determine the following:
We give: AB: adiabatic trigger such as VB = 2 VA AC: isothermal compression PA =1bar=105 Pa , VA = 10^-2 m3 Gas temperature at point A: TA= 300 Kelvin Perfect gas constant: R = 8,31 J.mol-1.K-1 Molar thermal capacity at constant pressure:Cp = 29 J.mol-1.K-1 Calorific capacity ratio of this gas: Cp/Cv = 1,40 4 – Calculate the amount of QBC heat and WBC work received by the system for the transformation that changes the system from state B to state C.5 – a – Why is the UCA internal energy variation of the gas zero during the CA transformation? b – Apply the first principle to the ABCA cycle and deduce the WAB work received by the gas during theadiabatic relaxation AB.c – Interpret the WAB sign.
Please answer with explanation. I will really upvote
A transverse traveling wave on a taut wire has an amplitude of 0.200 mm and a frequency of 500 Hz. It travels with a speed of 196 m/s. (a) Write an equation in SI units of the form y=A sin (kx - vt) for this wave.(b) The mass per unit length of this wire is 4.10 g/m. find the tension in the wire.
plz do this problem unable to understand explain all steps related to vibration dolve integration also properly and also find work done during 8 seconds
FIGURE P6.66 6.16 Calculate the natural frequencies and modal fractions for the system of Figure P6.16. 1000 N/m 2000 N/m FIGURE P6.16 4 kg 1000 N/m >2000 N/m 3 kg I
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.