Given a 2.0meter Wide Flange steel compression member with A=4832mm2, Ix=88951759mm4 and Iy=3223498mm4 with Fy = 345MPa. Calculate the allowable strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.

Given a 2.0meter Wide Flange steel compression member with A=4832mm2, Ix=88951759mm4 and Iy=3223498mm4 with Fy = 345MPa. Calculate the allowable strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A high-strength steel band saw, 29 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 290? Assume E = 210 GPa. Answer must be in mm.
A high-strength steel band saw, 27 mm wide, runs over pulleys 1000 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E =230 GPa. Answer must be in mm.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Calculate the design bending strength for the doubly reinforced rectangular section where A’s = 2500 mm2 f’c= 30 MPa & fy = 350 MPa if As =8500 mm2
What are common sources of groundwater contamination?
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
PLEASe answer this question. Thank you
Note: Read the question carefully and give me both right solutions with clear calculations. Don't copy from already available solutions.
Determine the maximum load that an 8 foot long 2"x4" rectangular aluminum alloy bar (E = 10.5x10^3ksi, σY = 40 ksi) can support with a factor of safety of 3 for both crushing and buckling if it has endconditions of:a. Pinned-pinned.b. Pinned-fixed.c. Fixed-free.d. Fixed-fixed.
For the steel truss and loading shown, determine the magnitude of the deformation (in inches) of member BE, knowing that the area is 3.58 sq. in, x = 12 ft, y = 7 ft, P = 26131 lb, and E = 29095755 psi. Round off the final answer to four decimal cross-sectional places. P A T P C P y B D X E
3. Determine maximum strength P for the bracket connection in the figure. ST37 steel is used for the connection, F = 2400kg /cm,F, = 3700kg /cm %3D %3D IPE200 15 cm P=? PL 250x150x15 mm te 7 mm, L=250 mm
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >