GET IX  With the node potential method .

Q: write a program using tinkercard, using one dimition called data.this array has patern of 0 and 1 tp…

A: We have to write a program using Tinkercard, using one dimension called data. This array has a…

Q: Differentiate the latching current from the holding current using a real-world example. You are not…

A: Latching current and holding current is the concept of SCR, To analyze the characteristics of SCR…

Q: 6. In the circuit below, calculate the load current, load voltage, load power, diode power, and…

A:

Q: Q2A. Use analoque computer components to implement a circuits to perform the following actions 1.…

A:

Q: Make a table of values that shows all calculations with the switch on verses the switch off. Make…

A: According to the datasheet of 2N3904,  Case 1 when a switch connected to the positive terminal of…

Q: What is short-circuiting? State one factor/ condition that can lead to it. Name a device in the…

A: Short circuiting: when live & neutral wires directly contact each other because of faulty wire…

Q: Define the unit step function and the shifted unit step function. Need

A: The unit step function and its shifted counterpart has been defied in the following section.

Q: perform the function in the picture only with or not gates.

A:

Q: Define the unit step function and the shifted unit step function. Need correct solution within 20…

A: The unit step function and the shifted unit step function have been defined in the following…

Q: Imnlement the simplified expression for the following figure using NOR gates only: X- F. C NOR Y)…

A:

Q: what was the calculation done to get d? Confused on how this was rearranged.

A:

Q: 5. In the figure, E₁ = 6.00 V. E= 12.0 V, R₁ = 100 S2, R₂ = 200 52, and R₁ = 300 2. What are the…

A: here we have to find the size and direction of currents through the resistors R1 , R2 , R3 .

Q: A. You are using 3 resistors (1000, 2.2kQ, 10KQ) in series, 3 LEDS are attached one after each…

A: Given, Using 3 resistors ( 100 Ω, 2.2 kΩ, 10 kΩ ) in series, 3 LEDs are attached one after each…

Q: How to turn-off a current source? A) Set it to zero. B) Replace it with a short-circuit. (C) You…

A: What is the process to turn of the current source  : Options are : Set it to Zero. Replace it with…

Q: Now we will use this knowledge of the code structure to make an LED Blink! Refer to Task 2 (page 7)…

A: We need to calculate the smallest resistor value.The Red LED has a forward voltage of  Volts.The…

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: told to not give in-correct solution. I need correct solution. Don't use ChatGPT and Good or Chegg…

A: Given sequential circuit is We need to determine the State table, state diagram and Boolean…

Q: Q21 Fill in the following blanks (Answer 5 only) 1.Switches in terms of number of contacts and…

A: Power system transfers power from the source end to the load end. Protection of the power system is…

Q: How to turn-off a voltage source? A) Set it to zero. B Replace it with a short-circuit. C) You can't…

A: This is a basic problem of circuit. The solution is given in the next step.

Q: Explain the following in one or two paragraph only.  1. Open circuit 2. Short Circuit

A: According to question, We have to explain the open circuit and short circuit.

Q: Define the unit step function and the shifted unit step function. Need

A: The solution is provided in the following section.

Q: What does Vripple represent? Which of the circuit components is responsible for the particular…

A:

Q: Use Visio to draw a circuit that implements an Exclusive OR circuit, using only basic gates.

A: To draw the XOR circuit using basic logic gate, first write the output function of the XOR gate. The…

Q: Please answer the "required" portion. Show full solutions with brief explanations and please DRAW…

A:

Q: Draw bread board connection diagram for full adders along with tables and pin configuration of ICs…

A: Full adder truth table: Thus, Sum, S=X⊕Y⊕Cin and Carry, Cout = (X*Y) + ((X⊕Y)*Cin) So, the circuit…

Q: Define the unit step function and the shifted unit step function. Need correct solution within 20…

A:

Q: Components Used: Part Values R1 22000 R2 600 Q Vsi 6V Vs2 3 V Table 1 1. Hand Calculation Analyze…

A:

Q: Explain in detail with drawing the basic operation of Wheatstone Bridge? [Hint: Arms of the…

A: The solution is given below

Q: The ladder diagram of AND gate will have two Normally open contact in series. Select one: True…

A: Given Ladder diagram of AND gate have two Normally open contact in series

Q: 4. What is the minimum number of 2-volt cells needed to make a 12-volt battery? A. 6 OB. 12 C.4 D.…

A: In this question, we need to determine the number of cells to make 12V battery.

Q: DISCUSSION 1. What is Wheatstone bridge? 2. State the advantages & disadvantages of Wheatstone…

A: Wheatstone bridge- It is the electrical circuit which is used for calculation of unknown…

Q: 2. Describe what you understand by overcurrents and indicate the protection devices that can be used…

A: Overcurrent is the condition in the electrical circuit when there is increase in the load current.…

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).