generated in standing warve string of length 3m toen with 1.Two waves nd praluce 3 loops b ormplitde Woves $beed is loom/s. ond ey.of Y (st) = Ym Sin(kxwt) the eg fox and waves find Ym ,k and w? ade ne Wave is in

Q: need help with part b i solved a prior

A: ◆ The mean effective pressure: 562.94 kPa. ◆ The indicated power developed by the engine is 4.10 kW.…

Q: Q/Draw S and B-M D 8 kuim

A:

Q: what is the speed ratio of v/U for part b?

A:

Q: Problem 109. Show that the expressions v = rw and ar = ra hold for the motion of the center O of the…

A:

Q: dy = m y2 dx

A:

Q: 5. ving gea Sun gear Arm planet gear The picture shows planetaury gear set : a A ssume the sun gear…

A: Given, 2 Sun gear 3 Arm 4 Planet gear 5 Ring gear T2=30T4=27 N5=0N2=101 rev/min

Q: How can we locate the position of the neutral axis?

A: Suppose a beam undergoes sagging bending, in this type of bending the upper surfaces undergoes…

Q: Write a note on different types of gear along with application.

A: The gears are used for power or torque transmission. They are generally used whenever the positive…

Q: n= 7

A: Kindly refer attachment for detailed answer.

Q: Lathe Machine tool is an example of three axes machines

A: Lathes, by definition, are 2-axis machines. Once machines advanced to incorporate 3-axis, 4-axis…

Q: y h с b bh .1

A:

Q: Explain the diagrame! C. Ca

A: Solution:   In the diagram, Cm is the Moment Coefficient. CL is the Lift Coefficient.

Q: Chip guard has to be installed between the point of operation and the operator, is a safety…

A:

Q: What is statically balance forces

A:

Q: very valuable fx anand fy

A:

Q: now the 12-tooth gear turn?

A:

Q: Lathe Machine tool is an example of three axes machines Select one: True False

A: The lathe machine tool axis - The cross slide (or turret) motion at a right angle to the spindle is…

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Q: QUESTION 2 vehicle's tires slip? 25 0.6 m 25 0.6 m 1.4 m Figure 2: A tractor and crate link

A: Given: The weight of the tractor, W = 1.5Mg The coefficient of friction between tyres and ground, f1…

Q: For Pitot tube, the fluid is given by : the velocity V = √2ghm hm = h. (&m - 1) St of develop the…

A:

Q: What are the parts of Milling Machine  (Make sure the parts are labeled accordingly)

A:

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: SI) Standard Sizes of Woodruff Keys 1210?

A: The dimension of ANSI 1210 KEY IS GIVEN AS

Q: thế časting part whose perspective pictures are given below, take into account the surface of the…

A: COVE DESIGN

Q: Lathe Machine tool is an example of two axes machines Select one: True False

A: The lathe machine tool is given

Q: Locate the centroid y of the area. Express your answer in terms of some or all of the variables a,…

A:

Q: Lathe Machine tool is an example of two axes machines Select one: True False

A: Solution:

Q: what is the value of Cx?

A: Fx= 12.662 kN. Using equilibrium condition in x direction for member FC.

Q: FGI and FKJ correct but incorrect afterwards.

A:

Q: 0le A. An outside caliper can be used to measure the diameter of a

A: Caliper is used to measure the linear dimension, diameter of a hole and outer diameter of a shaft.…

Q: Vibrations

A: given:

Q: The torque is incorrect please solve for torque

A: Power produced by the wheel angular speed of the wheel using the formula:Where T is the torqueP is…

Q: is the method of skewness used in ansys

A: The objective of the question is to understand if the method of skewness is used in ANSYS, a…

Q: Wipers pads on lathe machines are used between slides and slideways are designed to keep out cutting…

A: Wiper pads are typically made of felt that will hold oil. Wipers are designed to keep out small…

Q: Draw SFD and BMD

A:

Q: The open tank shown, which has a liquid with a specific gravity of S=12.7 as shown in the give…

A: As the fluid is accelerated upwards it will lead to pseudo acceleration(a) acting on the fluid in…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.