Gate AB of dimensions 0.5 x 0.8 m is located at a bottom of a water tank. The gate is hinged along top edge A and rests on a frictionless stop B. Find (a) the reaction forces at A and B when the cable is loose, (b) the minimum tension force T required to open the gate. C |D T 0.27 m 0.45 m A 0.48 m В

Q: Let F₁ = [F1] N and let F₂ = 350 N. g) Determine the magnitude FA of the force at pin A. h)…

A: Given data: F1= 839 N  F2= 350 N  Free Body Diagram of the member AB:

Q: Find out the reaction forces at fixed-end A, hinge B and rocker C

A: To find reaction at A and C and B

Q: Draw the influence line for member BC and interpret the diagram.

A: Solution: Considering the diagram of Truss: Applying a unit load at x from point A and find the…

Q: Determine the resultant force at pins A, C, and E. Also, determine the forces on pin D. y 80 kN/m 40…

A: in the given beam the transverse loading on the beam both shear force and bending moment my…

Q: F11-3. The linkage is subjected to a force of P = 2 kN. Determine the angle for equilibrium. The…

A:

Q: 0.15 m 0.4m 0.2 m 03 m 0.5 m 0.25 m 0.2 m

A: The position vectors and unit vector are as follows: rCD=(-0.2i-0.3j+0.25k) munit…

Q: The concrete dam is designed so that its face AB has a gradual slope into the water as shown. The…

A:

Q: 1O KNIM 60 KN 20 KNIM 48KN m A Fixed Pin/hirge 8 m 12 m C (Roller)

A: ∑MB=0 12×10×12×23×12 + 48 - RC×12 + 60×18 = 0 RC = 134 kN ∑V=0 RA+RC= 20×8 + 12×10×12 + 60 RA = 146…

Q: The pin at C has a diameter xx(see table below). Assume that the pin supports at C is stated at the…

A:

Q: The frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a…

A:

Q: 10 kN 10 kN 15 kN/m E A -B C D FIm Im 2 m Im

A: Given in question is beam with loading and it has been asked to find support reactions and Shear…

Q: Gate AB is semicircular and is held by force P at A. Determine the following: (a) A (m²), (b) h (m),…

A: Thank you for the question. As per honour code we have to answer first three subparts since exact…

Q: Problem 2: Replace the three forces which act on the bent bar by a force-couple system at the…

A: In this problem, we are given three forces acting on a bent bar. We must replace these forces with a…

Q: Consider the structure shown below. Determine the tension in the cable and the horizontal and…

A: Given: Weight of cylinder = 80lb

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: P=5.2KN

Q: he box girder below is subjected to a shear of V=15kN. Determine the shear flow at point B. Give…

A: The magnitude of the shear force on the box girder = V = 15 kN To determine:- a) The shear flow at…

Q: The structure below is supported by a pin at A and a roller at B. Determine the pin reactions at E,…

A: Reaction at pin E,C,D

Q: The two loads are suspended from the ABCD cable as shown. dC = Since it is known to be 2 m, the…

A: ##Calculate the reaction at support D And It's Components At D of cable ABCD Since bending moment…