G1 = 100, G2 = 1000 and H = 0.009 for two block diagrams as open loop and closed loop given in the figure. a. Find the output voltages when the input voltage is 10 mV. b. For both systems, when G1 and G2 are doubled due to temperature increase, what will be the output voltages even though the input remains at 10 mV? c. Interpret the above results using the system's sensitivity principle. G. G2 H

G1 = 100, G2 = 1000 and H = 0.009 for two block diagrams as open loop and closed loop given in the figure. a. Find the output voltages when the input voltage is 10 mV. b. For both systems, when G1 and G2 are doubled due to temperature increase, what will be the output voltages even though the input remains at 10 mV? c. Interpret the above results using the system's sensitivity principle. G. G2 H

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The data-input and data-select waveforms in Figure 7 are applied to the multiplexer. Determine the output waveform F in relation to the inputs.
Power electronics
a. b. C. There is a dc-dc converter that provides isolation between input and output current. Identify the converter type and describe the operation. Draw the equivalent circuit to support the explanation. Assume the converter operates in continuous-current mode. Explain why a switched -mode dc-dc converter is better that a linear regulator. As an electrical engineer, you are required to design a chopper circuit with an output voltage of 10 V from a 30 V input with switching frequency of 50 kHz. The circuit is operated in continuous current, and output ripple voltage is less than 0.8% with resistance load of 30 Q. Assume the inductor value is 50 % larger than Lmin and assume ideal components for this design. Identify the chopper type and construct the circuit with IGBT as the power switching.
EQUATION OF OUTPUT VOLTAGE( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
Ex) A standard two-junction thermocouple configuration is being used to measure the temperature in a wind tunnel. The reference junction is held at a constant temperature of 10 °C. We have only a thermocouple table referenced to 0 °C. Determine the output voltage when the measuring junction is exposed to an air temperature of 100 °C.
Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two approaches
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Vin?Vin = ____ volts
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Rin in ohms?Rin = ____ ohms
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? Cursor 1 I(R2) Horz: 22.204037ms Vert: 38.277447mA What is the value of Vin? No need to include the Units. Vin = volts
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? Cursor 1 I(R2) Horz: 22.204037ms Vert: 38.277447mA What is the value of Rin in ohms? No need to include the Units. Rin = ohms ----
Prob 1: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vb1, Vb2 are dc voltage sources. and I1 is an ideal dc current source. Ignore body effect for all problems. Vino M3 M₂ M₁ (a) VDD J Vb₁ M3 (e) VDD VinM₂ Vb2M₁ Vb3 Vb2 - Vout Vb1 Vout HE Vout o Vb₁ VinM₂ 46! M3 (b) VDD B M₁ T. M3H (f) VDD VinM₁ M₂ Vout VinM₂ 4M₁ (c) M3 M3 VDD VDD 74 Vb1M₂ Vino M₁ (g) Vout Vout Vb1 Vb2 HE Vin VinM₂ M3 M3 VDD (d) HL M₁ M₁ -o Vout M2o Vout 1₁ (h) VDD
1