G.. A water column in a glass tube is used to measure the pressure in a pipe. The tube is 6mm in diameter. How much of the water column is due to surface tension effects? What would be the surface-tension effects if the tube were (a) 3mm and (b) 1mm in diameter.

G.. A water column in a glass tube is used to measure the pressure in a pipe. The tube is 6mm in diameter. How much of the water column is due to surface tension effects? What would be the surface-tension effects if the tube were (a) 3mm and (b) 1mm in diameter.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Glycerin flows through a 50-mm-diameter horizontal pipe shown in (Figure 1) such that the pressure at A is PA = 113 kPa, and at B it is pa = 110 kPa. Figure Part A HÅ -3m T= Value Determine the magnitude of the shear stress that the glycerin exerts on the wall of the pipe. Express your answer using three significant figures and include the appropriate units. B. N/m² 1 of 1
A differential manometer is attached to a pipe as shown in figure below. Calculate the pressure difference between points A and B. (SG of Mercury = 13.6; SG of Oil = 0.95).
The pressure difference between two points as measured with a manometer is given as ?2 − ?1 = ??ℎ The following figure shows a single U-tube manometer for measuring pressure difference between points “A” and “B”. By determining the pressure at point “a” through the left leg and then through the right leg, show that the difference in pressure between point “A” ?? and “B” ?? is approximately given by ?? − ?? ≅ ?(ℎ2 − ℎ1)(??2?)
The closed cylinder shown is filled with water to a depth of 100mm and rest with air. What is the pressure at the bottom of the periphery of the tank? 0.02 0.10 AIR 0.20
Problem 5 In the figure shown, what is the static pressure in kPa in the air chamber? AIR 2.0 m OIL 4.0 m S=0.80 5.0 m WATER 3.0 m
Required information The figure shows a 400-mm-diameter brake drum with four internally expanding shoes. Each of the hinge pins A and B supports a pair of shoes. The actuating mechanism is to be arranged to produce the same force Fon each shoe. The face width of the shoes is 75 mm. The material used permits a coefficient of friction of 0.22 and a maximum pressure of 1000 kPa. Consider a = 0.150 m, R= 0.20 m, d= 0.050 m, and c= 0.165 m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 15° 15° F F 10 10 10 BY 10 FF 15° 15° Determine the following forces acting on the hinge pins of the brake. Rx1 (primary shoe) is kN. Ry1 (primary shoe) is kN. Rx2 (secondary shoe) is kN. Ry2 (secondary shoe) kN. The resultant force Ris kN.
Similitude Water flows through a 5 inch diameter pipe at 10 ft/s. If a test is performed using mercury moving at 4 ft/s, what diameter pipe (in inches) would be needed to maintain the same dynamic characteristics? Both fluids are at standard temperature and pressure. Hint: What dimensionless number do we use all the time for pipes?
A differential manometer is attached to a pipe shown. Calculate the pressure difference between points A and B.
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E-30,000 ksi, E10,000 ksil. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assombly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips 18 kips 34 kips 60 in. 40 in. 30 in.
What height of mercury column is equivalent to a pressure of 74 psig? The density of mercury is 498 Ibm/ft3. a. 11.28 ft O b. 21.40 ft c. 16.77 ft O d. 10.70 ft
A tube of diameter 25 mm is used (as shown in the below figure) as a siphon to discharge water from a large open vessel into a drain at atmospheric pressure, (Given: Atmospheric pressure = 101.325 kPa) ignoring friction losses (3) (1) Determine (a)Velocity of flow through syphon (b)Discharge through the syphon (c)The minimum pressure inside the syphon (2) 160 mm 80 mm, 100 mm
A 1200 Ibs force acts as shown on a 500 Ibs block placed on a horizontal plane surface. Determine the following: a. Coefficient of friction between the block and the plane surface. b. Determine whether the block is in equilibrium, and find the value of the friction force. If the Coefficient of friction between the block and plane surface are us = 0.30 and Hx = 0.25. 500 lbs 62°- 1200 lbs