g) How many cubic meters of crushed sand is required for mortar?h) How many cubic meters of fine sand is required for plaster?(apply 33% increase to sand for sifting)i) What is the order quantity for crushed sand and fine sand?(indicate separately) Figure 1: CHB WALL PLAN-10.0m-EXTERIOR WALLWALL TO BE ESTIMATEDINTERIOR WALL4.4mINTERIOR WALL4.4mNOTES:1) WALL IS 4" THK. CHB2) WALL IS 2.5m TALL3) 10mm HORIZONTAL RSB @ EVERY 2 LAYERS4) 10mmø VERTICAL BARS SPACED @ 0.4m 0.c.5) 1:3 PROPORTION TO BE USED FOR MORTAR6) ROUGH AND FINE PLASTER TO BE APPLIED ONLY TO INTERIOR WALLS7) ONLY ROUGH PLASTER TO BE APPLIED TO EXTERIOR WALLS

Answered: Image /qna-images/answer/6aa4d555-d7ba-45a9-aa6c-fa84edb9cec3.jpg

g) How many cubic meters of crushed sand is required for mortar? h) How many cubic meters of fine sand is required for plaster? (apply 33% increase to sand for sifting) i) What is the order quantity for crushed sand and fine sand?

g) How many cubic meters of crushed sand is required for mortar? h) How many cubic meters of fine sand is required for plaster? (apply 33% increase to sand for sifting) i) What is the order quantity for crushed sand and fine sand?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the volumes of the hydration products for 150 gm of cement with 0.5 w/c ratio, assume…

A: It is required to determine the volume of dry cement actually hydrated. Vcah=Weight of dry cement…

Q: You are working on a concrete mix design that requires each cubic yard ofconcrete to have 0.45…

A: Given that; w/c ratio=0.45 Mass of cement=335 kg/m3 , Gcement=3.15 Air content=4% Mass of dry…

Q: Q1- What is the purpose of using cement-sand mortar rather than cement paste for determining the…

A: Q-1 Using only cement to make mortar has many of problems. Like - -large amount of shrinking of…

Q: Q#1. Define Durability? Explain the physical and chemical causes of inadequate durability. (CLO2) a:…

A: In civil engineering, the building materials are used according to their properties such as…

Q: How to compute the required water for the initial time setting of Portland Cement? Please include…

A: Standard consistency test is conducted to find out the amount of water to be added to the cement to…

Q: 8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse…

A: 8. What is the maximum allowable limit of Materials Finer Than 75 Mm (No. 200) Sieve in Coarse…

Q: For determination of initial setting time use the following data: Time Penetration 30 min 40 mm 40…

A: To find the weight of water required

Q: What type of cement would you use in each of the following cases? Why?a. Construction of a large…

A: Since we answer only first three sub-parts so we will answer the first one. Please resubmit another…

Q: Determine the following: a. The compressive strength of each cube. b. The average compressive…

Q: A concrete mix has been designed as follows with a target characteristic compressive strength of 32…

A: Reference : ACI mix design 311The adjusted water can be defined as ;Where ;MC = Moisture contentAC =…

Q: 1. (a) The data presented below is compiled to obtain the modulus of rupture values of the MgO…

Q: Q2:-From the sieve analysis (grading test), the following results are obtained: Sieve size, ASTM…

A: sieve size wt. of aggregate retained on each cumulated % retained by wt % passing by wt…

Q: Determination of Normal Consistency of Hydraulic Cement Calculation Calculate the amount of water…

Q: The following laboratory tests are performed: o Setting time test of cement paste samples o…

A: Finding out the test.

Q: please answer all questions ,thanks ! (a)What has cross-sectional shapes? (b)What commonly used…

A: (a)What has cross-sectional shapes? (b)What commonly used type of cross-sectional study? (c)Why is…

Q: Estimate quantity of given items below of given plan and scction below Hints o Redraw the Table#1…

A: Note : As per guidelines only 3 parts can be solved if you wish for the other parts please repost…

Q: EXAMPLE:- For the plan shown below; Estimate number of ( blocks) and amount of cement & sand. If the…

Q: What is the quantity of cement (in kg) and of dry sand (in cubic meter) respectively required for…

A: Cement mortar proportion = 1:5We are asked to determine the quantity of cement and dry sand ?

Q: Calculate the weight of cement, fine aggregate (sand), coarse aggregate (rock) and gallons of water…

A: Given Data: pad dimensions=5ft×5ft×5inmix=1:2:4w/c=0.50 The maximum coarse aggregate size as per…

Q: the compressive strength is 30.68 MPa, water - cement ratio is 0.45, and coarse aggregate is 992…

A: If the compressive strength is 30.68 MPa, water - cement ratio is 0.45, and coarse aggregate is 992…

Q: Four standard mortar cubes were made using nonpotable water available atthe job site, and four…

A: Calculate the average compressive strength using given table values for non-potable water:…

Q: The water cement percentage for Normal Consistency of Cement is 35%. The volume of water is 180mL.…

Q: Q2: Concrete is required for a building foundation. Soil testing shows that the level of…

A: From ACI 318 we have below two table Table 1: Maximum Water-Cementtitious material ratios and…

Q: Q3) Answer the followings: 1-Under what conditions would you recommend the use of sulphate resisting…

A: Cement: A cement is a binder or a substance that sets and hardens independently and also which can…

Q: What is the factors affecting the strength of cement paste?

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: From the following Figure 1-23, find the cement, sand and gravel if there are 8 columns, using class…

Q: How does the increase of maximum aggregate size used in the concrete mix design affect the…

A: Increase of maximum aggregate size used in the concrete mix design affect the percentage of fine…

Q: Three mortar mixes were prepared with water to cement ratios of 0.50, 0.55, and 0.60. Three 2-in.…

A: Given: Width of mortar cubes = 2 in

Q: 2. Calculate the gel/space ratio and theoretical strength of a sample of concrete made with 500 gram…

A: The given data is: Cement=500 gm W-C ratio=0.5 Hydration=60%

Q: ent number amount of cement thinness (cm components (%) İnceli (cm2/c 4800 nento Çimento…

A: The cement No.1 will be more suitable for working in hot environment.

Q: 6.32 The results of an experiment to evaluate the effects of a water reducer are shown in Table…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: DATA: Amount of Cement = 650 grams Amount of Water = 195 grams Calculate the amount of water…

A: Given data: Amount of Cement = 650 grams Amount of Water = 195 grams It is asked to Calculate…

Q: EXAMPLE:- For the plan shown below; Estimate number of (blocks) and amount of cement & sand. If the…

Q: Tennis court, subjected to freezing Required design strength =21 MPa Slab thickness=300 mm…

A: given data : design strength =21 MPa Slab thickness=300 mm standard deviation of compressive…

Q: Pick out the correct statements from the following (Note: there may be more than one correct…

A: Cement with greater specific surface area set faster than lower specific surface area cement. So…

Q: Q1) Define the C-S-H phase of cement paste.

A: Note : Since, you have posted multiple questions... we will provide solution for only the first…

Concept explainers

Types of Cement

Cement is a fine mixture of limestone, chalk, or marl and clay which when mixed with water, becomes compacted due to the formation of strong molecular bonds. Due to hydration, cement turns into a hard mass when left for a sufficient amount of time upon mixing with water. The water turns the cement compounds into gel-like submicroscopic particles having higher surface areas. It is due to the hydration properties of cement, they are often known as hydraulic cement. For instance, Portland cement is a popular example in this category.

Question

g) How many cubic meters of crushed sand is required for mortar?
h) How many cubic meters of fine sand is required for plaster?
(apply 33% increase to sand for sifting)
i) What is the order quantity for crushed sand and fine sand?
(indicate separately)

Figure 1: CHB WALL PLAN
-10.0m-
EXTERIOR WALL
WALL TO BE ESTIMATED
INTERIOR WALL
4.4m
INTERIOR WALL
4.4m
NOTES:
1) WALL IS 4" THK. CHB
2) WALL IS 2.5m TALL
3) 10mm HORIZONTAL RSB @ EVERY 2 LAYERS
4) 10mmø VERTICAL BARS SPACED @ 0.4m 0.c.
5) 1:3 PROPORTION TO BE USED FOR MORTAR
6) ROUGH AND FINE PLASTER TO BE APPLIED ONLY TO INTERIOR WALLS
7) ONLY ROUGH PLASTER TO BE APPLIED TO EXTERIOR WALLS

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

State the uses of the following materials. Give also the reasons. (1) Portland Pozzolan cement. (2) Modified Portland cement (3) Roofing tiles. (4) Sulfate resistant cement. (5) Designer tiles (6) Quartz powder and quartz chips (7) Lime (8) Flooring tiles B: What is the purpose of adding gypsum while manufacturing cement?
What is the amount of cement in kilograms needed for the design mix? Use two decimal places
Reference Table: Quantity of Cement and Sand for mortar and plaster in Properties: Length of wall (1) = 4.0 m, use 6" thick CHB; Size cubic meter of door: 0.90 m x 2.10 m Length of wall (2) = 5.0 m, use 6" thick CHB; Size of window: 1.50 m x 2.20m TABLE 2-1 QUANTITY OF CEMENT AND SAND FOR MORTAR AND PLASTER IN CUBIC METER Class Moture Cement in Bags 40 kg Sand cu. m. Proportion Length of wall (3) = 4.0 m, use 4" thick CHB 50 kg 1:2 1:3 1:4 1:5 18.0 12.0 9.0 7.5 14.5 9.5 7.0 6.0 1.0 1.0 1.0 1.0 Height of "A" from floor line to bottom of beam = 2.80m Height of "B" from the ground line to floor line Your answer 0.30m Height of "C" from ground line to bottom of CHB = 0.30m Determine the quantity of 6" CHB for walls 1, 2 and 3. Your answer Quantity for cement in 40-kg bag used as core filler and block laying Your answer 5500
Considering the data in the table below; Select the cement type suitable for concrete production in cold weather conditions and explain the reasons.
**Compute the volume of cement solids per bag of cement in cu m. a. 0.024 b. 0.042 c. 0.012 d. 0.021**Compute for the required volume of sand solids per bag of cement. a. 0.0401 b. 0.302 c. 0.0104 d. 0.0203**Compute for the volume of concrete that can be produced per bag of cement a. 0.1461 b. 0.1061 c. 0.1262 d. 0.0661
Find the quantity of 15 cm x 20 cm x 40 cm CHB, 50 kg. cement per bag, sand and gravel required using class "B" mixture by Area Method.
How to compute for required water for initial setting of Portland cement? Show the solution.
Discussion 1- Compared between water / cement ratio required for standard consistency with range specified by American standards ASTM? 2- Discuss the results of your group with other groups? 3- What is the factor affecting the measurement of standard consistency of the cement paste?
Determine the amount of water needed to achieved the normal consistency of 650 grams cement by using Vicat apparatus. The paste shall be of normal consistency when the rod settles to a point 10 ± 1 mm below the original surface in 30 seconds after being release. Determine the moisture content in percent if the rod penetration is 11 mm.
Determine the quantities of materials required per cubic yard to create a concrete mix. The specifications require a maximum size aggregate of 1 1/2 in., a minimum cement content of 5 1/2 sacks per cy, and a maximum water-cement ratio of 0.63. Assume 5% air voids.