G₁ = -4%; G₂ = + Sta. P = 5 +850; Elev. P Sta. BVC = 5 + 680; Elev. B swer: + 162, Elev. EVC = 200.18 m L = 481.67 m, STA. Lowest Point = 6 +001, E

Q: Which of the following terms describe shear rupture failure in block shear

A: shear rupture is type of failure occurring in the member that have both tension  on one plane and…

Q: What the deviator stress?

A: The deviator stress can be defined as it is the difference between the principal major and minor…

Q: Input the Bearing value shown below in the answer box: -Please be sure to use the ddd.mmss format in…

A: Given Data- Given bearing S 23o 02' 11"W It is needed to convert this bearing as per the given…

Q: Define undrained condition

A: If water is not allowed to flow in or out of the soil,  the stress path is called an undrained…

Q: Reasons and defects for floors men

A: Solution: Proper floor care is needed for every aspects of business like for carpet, wood or Tile…

Q: From the figure. Determine the number of 15x20x40cm CHB required to construct the building firewall…

A:

Q: Give details of JPCP, JRCP, and CRCP with necessary figures.

A: In pavement construction, three different concrete pavement design types are commonly used: Jointed…

Q: 4. Explain the procedure of any one type of surface rendering. 5. Explain the term DPC and how it…

A:

Q: How is the cut and fill calculation done?

A: Cut and fill Excavation: It is also known as excavation and embankment. This is a  process in which…

Q: What were fly-ash ESPs?

A: An electrostatic precipitator is defined as a filterless device that excludes fine particles, for…

Q: Define scour

A: Scour is the removal by hydrodynamic forces of granular bed material in the vicinity of coastal…

Q: A setup similar to the one shown in Figure 10.35 is commonly used to mea- sure the shear modulus, G.…

A: Given: The torque is 3450 N.m. The length of the specimen is 20 cm. The diameter of the specimen is…

Q: Given a simple floor plan, compute for: a. Concrete materials b. Masonry materials

A: Given Data: The length of a longer wall is 10.00 m The length of a shorter wall is 8.00 m The height…

Q: Give the applications of dry–dry scrubbing system?

A: The applications of dry–dry scrubbing system area as follows. It is used to remove less…

Q: Dewfine the term final completion?

A: During the closing process of the project, the final completion-also recognized as final approval is…

Q: GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS

A: Disadvantages of using hollow blocks are : High Maintenance cost Load bearing capacity of the wall…

Q: The information shown in this attached document. This has been extracted from the Expert Panel…

A: The order of construction in civil projects can vary depending on the specific project and its…

Q: Define Allowable Stress Design

A: Their are mainly two type of design concept: Allowable stress method Load and resistance factor…

Q: Define The shape of the loaded area

A: The shape of loaded area describes the intensity of loading at different sections and it's variation…

Q: Define Vacuum Consolidation.

A: Vacuum consolidation is defined as the technique which is used for improving  the property of soft…

Q: * Standard Reference of Atterberg Limits Test is ASTM D 8215 O ASTM D 4318 O ASTM D 6523 O ASTM D…

A: The ASTM D 4318 gives the standard test procedures for determination of liquid, plastic and…

Q: potential design fault in the structure of Citicorp building New York

A: Since the building's skeleton was compromised by the presence of stilts in the centre of each side,…

Q: Description of Consolidation Procedure.

A: compressibility - the compressibility of the soil is defined as gradually decrease in volume of soil…

Q: 13. _________ is the process to determine the overall cost of project’s construction. Fill in the…

A: Processes of cost estimation are Empirical cost inference. Unit cost of bill of quantities. Types…

Q: Which calculating methods are used to determine the roofing sheet

A: Roofing materials are always represented based on area with unit meter square. Each type of material…

Q: What are Wet-Impingement Scrubbers?

A: Wet-Impingement Scrubbers:

Q: he accuracy of the spread plate metho

A: The spread plate method is generally the technique to plate the sample of liquid that contains…

Q: What is consolidation test?

A: - Consolidation test is used to calculate the rate of consolidation and and magnitude of soil…

Q: What is the PreProposal meeting?

A: Pre-proposal meetins:

Q: GEOFOAM Methodology - How is this material installed and/or maneuvered around site?

A:

Q: Define Earth pressure loads

A: Pressure is defined as force acting per unit area of the body.

Q: what method did you use there

A: For forces in member , method of joints have been used and for displacement calculation virtual work…

Q: ESSAY Advantages and Disadvantages of Using Hollow Block

A: Hollow blocks are generally prepared with aerated concrete . These block have both advantages as…

Q: (2) 6 21 28" 4 Uncracked M = 30' foop = ? foot = ? Mer=? ft-k

A:

Calculation of Settlement

The vertical displacement of the structural foundation due to the loading from the superstructure is known as settlement. It is due to the reduction of air voids present in the soil. The amount of vertical displacement depends on the bearing capacity of the soil on which the foundation is laid. The effect of the settlement depends on the magnitude of settlement, uniformity, and the structural design of the structure. The maximum allowable settlement for residential and office buildings should be less than 18 mm, for industrial buildings, it is 38 mm and for commercial buildings, it is 25 mm.