Fuel Stack Combustion gases to stack Boiler AirD Turbine Electric generator Condenser Warm water Feedwater pump Pump Makeup water Cooling tower Cooled water A chemical plant currently purchases 2.4 x 105 MW.h of electricity annually from the local utility provider. An aging boiler in the local provider's facility provides 4 x 108 kg of process steam at 20 bar. Consider the feasibility of a new system to meet the need of the steam and electricity. This system will use turbine to produce the electricity and a heat- recovery steam generator to produce the steam. Write a technical proposal for your proposed system.

Fuel Stack Combustion gases to stack Boiler AirD Turbine Electric generator Condenser Warm water Feedwater pump Pump Makeup water Cooling tower Cooled water A chemical plant currently purchases 2.4 x 105 MW.h of electricity annually from the local utility provider. An aging boiler in the local provider's facility provides 4 x 108 kg of process steam at 20 bar. Consider the feasibility of a new system to meet the need of the steam and electricity. This system will use turbine to produce the electricity and a heat- recovery steam generator to produce the steam. Write a technical proposal for your proposed system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Part a) and Part b) are separate questions to be solved independently. Part a) A vapor-compression…

Q: Show the COMPLETE SOLUTIONS and DIAGRAM (T-8) (Cycle) including the switching of table and…

Q: A schematic of a combined refrigeration cycle and a portion of a steam power cycle is shown in the…

A: It is asked to find the turbine work output

Q: Based on the analysis of steam power plant having condenser, why thermal efficiency of power plant…

A: Write the expression for the efficiency of the steam power cycle. Here TL represents the ambient…

Q: Problem 2 – Heat Pump Thermodynamic Analysis Refrigerant-134a enters the condenser of a residential…

A: Given-The inlet pressure at condenser is The inlet temperature at condenser is The volume flow rate…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses…

Q: WATER IS USED AS THE WORKING FLUID IN AN IDEAL RANKINE CYCLE STEAM ENTERS THE TURBINE AT 20MPA AND…

A: given; →net workoutput(wnet)=?→heat transfer in steam generator (Q1)=?→thermal efficiency (η)=?→heat…

Q: The resistance force R of a supersonic plane during flight can be considered as dependent upon the…

Q: A cogeneration system works with a water cycle and a refrigerant (ammonia) cycle combined.…

A: Note: for properties at any point refer property chart of the fluid involved. First draw the T-S…

Q: (i) List the name of the four processes in a generic Carnot cycle and state what type of energy…

A: Carnot cycle : A Carnot cycle is a theoretical perfect thermodynamic cycle suggested by Sadi Carnot,…

Q: A Carnot cycle operates between 30 deg C and 300 deg C. If the heat added is 1200 KW, find the work…

Q: create a diagram of the geothermal energy flow in a geothermal power plant.

A: Draw the block diagram of the geothermal energy flow in a geothermal power plant

Question

Fuel-
Air
Stack
Combustion gases
to stack
Boiler
Turbine
Electric
generator
Condenser
Warm water
Feedwater pump
De
-Pump
Makeup water
Cooling tower
Cooled water
A chemical plant currently purchases 2.4 x 105 MW.h of electricity annually
from the local utility provider. An aging boiler in the local provider's facility
provides 4 x 108 kg of process steam at 20 bar.
Consider the feasibility of a new system to meet the need of the steam and
electricity. This system will use turbine to produce the electricity and a heat-
recovery steam generator to produce the steam.
Write a technical proposal for your proposed system.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step by step

Solved in 8 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A power plant using a Rankine power generation cycle and steam operates at a temperature of 81.25°C in the condenser, a pressure of 5 MPa in the boiler and a maximum boiler temp of 775°C. The cycle operates at steady state with a mass flow rate of 2.5kg/s. Use the steam tables in the appendix of Sandler (p. 917 to 925). a.) Draw out the cycle, calculate the work required for the pump, the work output by the turbine, the heat into the boiler, and the heat out of the condenser. b.) What is the efficiency of this power plant? c.) If the turbine was only 89% efficient but still adiabatic (only generates 89% of the calculated work from part b), what is the overall efficiency of the cycle?
A steam power plant works between 40 bar and 0.05 bar. If the steam supplied is dry saturated and thecycle of operation is Rankine, find :(i) Cycle efficiency (ii) Specific steam consumption
Determine Wp
1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
Determine: a)Work of the compressor(kW) b)COP of the cycle
A boiler plant incorporates and economizer and air preheater and generates steam at 40 bar and 300oC with fuel heating value of 33000 kg/hr. The temperature of feedwater is raised from 40oC to 125oC in the economizer and the flue gases are cooled at the same time from 395oC to 225oC. The flue gas then enters the air preheater at a pressure of 1.2 bar and 16oC with a pressure rise across the fan of 18 mm of water. The power input to the fan is 5 kW and it has mechanical efficiency of 78%. Neglecting heat losses and assuming the flue gases as ideal gas with constant specific heat of Cp = 1.01 kJ/kg-K, calculate: (a) the mass flow rate of the air, (b) the temperature of flue gases leaving the plant, (c) the mass flow rate of the steam, and (d) the efficiency of the boiler.
a) Heat leaks from the air in a kitchen through the walls of a refrigerator into the refrigerated cold space at a rate of 0.3 kW. The refrigerator operates in an ideal vapor compression refrigeration cycle between 1.2 bar and 9 bar. It uses refrigerant R-134a as the working fluid. Determine the coefficient of performance of the refrigerator.
Write legibly, provide manual step by step solution, and diagram for below given problem. A supercritical power generates steam at 25 Mpa and 560. The condenser pressure is 7 kpa. Determine the exit quality of steam if it expands through a turbine in this power plant. a. 45.66% c. 56.66%b. 68.45% d. 74.26%
In a steam power plant operating according to the simple ideal Rankine cycle, steam enters the turbine at 10 MPa pressure and 600 ° C temperature and condenses at 30 kPa pressure. The isentropic efficiency of the turbine and the pump is 90%, the steam flow circulating in the cycle is 25 kg s. a) The power generated in the cycle, b) The heat thrown into the environment in the condenser c) Calculate the thermal efficiency.
8.
Refrigeration system Present step by step solution. If EB in to be used, start in System Under Study, then, Fluid Under Study, and draw BED.