From the following figure, find the number of 10 mm lateral ties and tie wire if there are 36 columns with cross sectional di- mensions of 60 x 90 cm. at 12.00 meters long per column. 10 - 25 mm main reinforcement 90 m Lateral Ties 60 m. CROSS SECTION .80 m. FIGURE 3-17

Q: Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown.…

A: d (effective depth) = 430mm

Q: A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel…

A:

Q: Two wooden planks, each 18 mm thick and 250 mm wide, are joined by the glued mortise joint shown.…

A: Given Thickness 18 mmLoad  19 kNCut d = 30 mmTo find out Maximum ave shear stress

Q: Design a slender unbraced rectangular column with the following data : Size of column 25 cm x 30 cm…

A:

Q: From the above figure, determine the numbe a. 10 x 20 x 40 cm CHB b. Vertical reinforcement spaced…

A: I have solved your problem

Q: Q1: For the simply supported beam of the cross sectional dimensions and load shown in the figure,…

A:

Q: The slender, 180-kg beam is suspended by a cable at its end as shown in (Figure 1). A man pushes on…

A: Given, M = 180 kg  F = 35 N

Q: Example 3: The beam shown below has a cross section of channel shape with width b-300 mm and height…

A:

Q: Q2. The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service…

A: The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service…

Q: A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are…

A: sagging of beams : The sagging of beams is referred to as "deflection" in the construction industry.…

Q: Weight of Crate : 200kg Rope Tension Limit: 10KN Determine the smallest angle. Determine Force AB

A: Given Data: The weight of the crate is m=200 kg The rope tension limit is FAC=10 kN   To Determine:…

Q: Design Beam AB: The beam carries the distributed loads and the concentrated loads as shown: Select…

A: Answer  (1) Selection of section In order to select a section we need to equate Maximum Moment on…

Q: girder properties: A = 11500 mm² d. = 350 mm b = 250 mm = 16 mm tf t₁ = tw = 10 mm Properties 1x =…

A: Given:- A=11500mm 2 bf=250mm d=350mm tw=10mm Fv=99MPa Ix=266 X 10 6 mm4  Iy=45 X10 6 mm4 To find:-…

Q: The geometry and reinforcement configuration of the column is given below. The material properties…

A: fy=420 MPafc'=30 MPab=400 mmh=600 mmDesign axial load=1250 kNDesign moment=550 kN

Q: 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum…

A: Load P = 50KN Allowable shear stress = 70MPa Bearing stress = 40MPa

Q: Example 3 Estimate the steel reinforcement for the Column as Shown in figures below $-010mme10am…

A: To find the total amount of steel required in the column Longitudinal reinforcement= 8 bars of 16…

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P =…

A:

Q: Fundamental Problem 3.11 The 165-1b crate is supported by cables AB, AC, and AD. Determine the…

A: Using vector analysis express the tensile forces in cables as vectors. Then using equilibrium…

Q: Given a 10"X16" reinforced concrete beam section as shown. The main reinforcing rebars consist of…

A: f'c=3000 psify=60 ksiTo determine:Theoretical nominal bending moment

Q: Problem: Using WSD & USD, design the midspan reinforcement of stringer (B-3) for the second floor of…

A: Assuming thickness of slab S3 and S4 as 150 mmf'c=20.7 MPafy=280 MPa (Grade-40 steel)γc=24.5…

Q: Find Internal External Find and draw SMT Diagrams

A:

Q: 75 mm - 300 mm Exercise #3: The short legs of four 6" x 4" x ½" angles are connected to a web plate…

A: The essentials of mechanics sound more appropriate to the structure of airplane and boats and…

Q: What is the ultimate uniaxial load capacity of the given column section, according to the design…

A: For the given problem, we will use the minimum eccentricity formula to solve for ultimate load…

Q: A short tied column carries an axial dead load of 600 kN and a 800 kN live load. Using 2% gross…

A: Given data Fy = 276 MPa Fc' = 20.68 DL = 600 KN LL = 800 KN

Q: : The continuous beam shown in figure below ha a positive reinforcement consists of (4#19 bars)…

A: Consider the cross-sectional layout of the beam Calculate the factored load on the beam

Q: What the Top and Bottom reinforcement at area A in X- direction ? (you can use the symbol Ф) * 6.0-…

A: Dia 12 at 200 mm spacing  is the answer

Q: Design Shear ReinForcement For a beam Shown below. It's Size is 350 x 600· It's effective depth is…

A: Given : l=6.3m b=350 mm d=525mm Fe280  Assuming grade M20 of concrete Ast =         =3*(3.14/4)*82…

Q: Six 20-mm-diameter rivets fasten the plate to the fixed member. Determine the shearing stress caused…

A:

Q: Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will…

A:

Q: ties and tie wire if there are 36 columns with cross section mensions of 60 x 90 cm. at 12.00 meters…

A: Given:- lateral  ties dimater=10mm number of columns=36 60 x 90cm L=12.00metres=1200mm To find:-…

Q: Fundamental Problem 3.11 The 165-lb crate is supported by cables AB, AC, and AD. Determine the…

A:

Q: The application of fluid mechanics theories involved in the system. How to reduce the energy losses…

A: The important fluid mechanics theories are  i. Continuity equation ii. Momentum equation iii.…

Q: Six 7/8-in-diameter rivets fasten the plate in Figure below to the fixed member. Determine the…

A: It is given that :

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.