From the figure below, assume 2 K1 =1.2 K2 = 2.7 K3 = 3 K4 and that layer 2 and 3 are of equal heights. AB = 8 cm, BC = 12 cm and CD = 10 cm. All remaining units are also in cm. K2 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 3.5 x 10^2 cm/s (IN 2 DECIMAL PLACES) 28

From the figure below, assume 2 K1 =1.2 K2 = 2.7 K3 = 3 K4 and that layer 2 and 3 are of equal heights. AB = 8 cm, BC = 12 cm and CD = 10 cm. All remaining units are also in cm. K2 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 3.5 x 10^2 cm/s (IN 2 DECIMAL PLACES) 28

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The structure shown below consists of an arch AB and an elastic column BC. Joints where members meet can be treated as pin. Calculate the weight that causes the column to buckle. Determine the support reactions corresponding to the weight from the previous question.
Replace the forces acting on the bar by a resultant force and a couple moment about point A. Specify the distance x from point A to the line of action of R.
Determine the vertical displacement of joint C. The length, L, of trusses AC, BC is 1,000 mm. The applied force at joint C, is 9.5 kN. The cross-sectional area of both trusses, A, is 370 mm2. The elastic modulus of truss AC, E1, is 115 GPa. The elastic modulus of truss BC, E2, is 155 GPa.
A=5 B=5 C=5
In the figure below , A, B , and C are all pin-connected , while D and E are fixed. With x = 11.6 what is the horizontal support reaction (in kips or k units) at C? Approximate final answers up to two decimal places.
With reference to the figure below, the total force (F) of the liquid on the plane surface and the location of the center of pressure (yp) are defined as: A. F = yhA C. F = yhA ; ; Free surface p = 0 Inclined plane area (side view) Yp = y + i yA i Yp = y +- yA Yh dA c.p. Inclined plane area (view from above) Centroid dy dA B. F = yhA D. F = yhA ; ; O I yA i Yp = y +- Yp = y + yA
The triangle section AB beam, bearing the load F1 = 400 dan in the figure, is produced from a material with a maximum shear stress of 1800 daN / cm2. If the base length of this beam, which is forced to bend under F1 load, is b = 8 cm, how many cm should its height (h) be in order to carry this load 3 safely? (The weight of the beam will be neglected) F1=400 dan 300 cm 100 cm 38 - Davanım Momentleri W= Cm bh? bh? 24 d3 D* -d* b 10 10D b O A) 10,5 O B) 19,5 O C) 12, 25 O D) 15 O E) 17,25
For the figure shown, let a = 200 mm and b = 95 mm. b/2b/2 a e a/2- - a/2→ Calculate the moment of inertia about the x-axis.
Use 4 decimal places during computation and 2 decimal places for the final answer. Please write you’re your solution on a paper and draw the FBD.
Consider the truss shown in (Figure 1). Take A = 0.0015 m? and E = 200 GPa for each member. Suppose that F = 8 kN. Part A Determine the force in member 6 of the truss and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA 96 =- 7.551 kN Figure 3 4 m F
From the force system shown, determine the the horizontal component of the force T Q = 200 lb Y. P = 722 lb 60 20 F = 448 Ib T = 400 lb
SITC. Determine the horizontal displacement (mm) of joint C. 300 lb 300 lb 13 ft B 5 ft 12 ft 13 ft 12 ft